WLCA27TS Omron, WLCA27TS Datasheet - Page 41

• Manufacturer Part Number: WLCA27TS
• Description: SWITCH
• Manufacturer: Omron

Specifications of WLCA27TS

• Rohs Compliant: YES
• Actuator Style: Roller Lever
• Operating Force Max: 10.2N
• Contact Voltage Ac Max: 125V
• Contact Voltage Dc Max: 8V
• Contact Current Ac Max: 10A
• Contact Current Dc Max: 10A
• Switch Terminals: Screw

Using the Switches
Changing the Installation Position
of the Actuator
By loosening the Allen-head bolt on the
actuator lever, the position of the actua-
tor can be set anywhere within the 360°.
With Indicator-equipped Switches, the
actuator lever comes in contact with the
top of the indicator cover, so use caution
when rotating and setting the lever.
When the lever only moves forwards and
backwards, it will not contact the lamp
cover (except for long-life models).
Changing the Orientation of the Head
By removing the screws in the four cor-
ners of the Head, the Head can be set
in any of the four directions. Be sure to
change the plunger for internal opera-
tions at the same time. (The operation-
al plunger does not need to be
changed on general-purpose and high-
sensitivity overtravel models.) The roll-
er plunger can be set in either two po-
sitions at 90°.
WLCA2-2N and WL01CA2-2N can be
set only in either the forward or back-
ward direction.
Changing the Operating Direction
By removing the Head on models
which can operate on one-side only,
and then changing the direction of the
operational plunger, one of three oper-
ating directions can be selected. For
overtravel 90° operation models, one
of three operating directions can be se-
lected by loosening the rubber holder
using either a coin or a flat-blade
screwdriver and changing the direction
of the internal rubber section.
The tightening torque for the screws on
the Head is 0.78 to 0.88 N•m.
Item
Roller Levers:
WLCA2, WL01CA2, WLCA2-2,
WL01CA2-2, WLH2,WL01H2, WLG2,
WL01G2, WLMCA2@, WLMH2@,
WLMG2@, WLMGCA2@
Adjustable Roller Levers:
WLCA12, WL01CA12, WLCA12-2,
WL01CA12-2, WLH12, WL01H12,
WLG12, WL01G12,
Adjustable Rod Levers:
WLCL, WL01CL, WLCL-2, WL01CL-2,
WLHL, WL01HL, WLGL, WL01GL
Roller Levers:
WLCA@, WL01CA@, WLCA@-2,
WL01CA@-2, WLGCA@, WLH@,
WL01H@, WLG@, WL01G@,
WLMCA2@, WLMH2@, WLMG2@,
WLMGCA2@
Adjustable Rod Levers:
WLCL, WL01CL, WLCL-2, WL01CL-2
Horizontal Plungers:
WLSD@, WL01SD@
Top-roller Plungers:
WLD2, WL01D2
Sealed Top-roller Plungers:
WLD28, WL01D28
Does not include -RP60 Series or -141
Series.
Roller Levers:
WLCA2, WL01CA2, WLGCA2,
WLMGCA2@
Adjustable Roller Levers:
WLCA12, WL01CA12
Adjustable Rod Levers:
WLCL, WL01CL
Overtravel Models:
WLCA@-2N, WL01CA@-2N
Applicable models and Actuators
One-side Operation for General-purpose and High-precision Switches
Cam Direction Changing Procedure for Overtravel, 90° Operation Switches
Relationship of cam to operation as observed from the rear of Switch
Operating Operating
Loosen the cam holder with a
coin or screwdriver. Take out
the cam from the Switch.
The output of the Switch will be
changed, regardless of which
direction the lever is pushed.
Head
Does not
operate
Operation in both
directions
Operates
Operation on both sides
Operation on one side
Loosen the screws.
Not operating
Operates
Loosen the M5 × 12 bolt, set
the actuator's position and then
tighten the bolt again.
Operates
Clockwise operation
Details
Operating
Operates
Operation on one side
Change the direction of the cam as
required by your intended operation
and then reinstall the cam.
The output of the Switch will
only be changed when the lever
is pushed in one direction.
Operating Not operating
Avoid this combination
Counterclockwise
operation
Does not operate
WL/WLM
Head
Loosen the screws.
Operational
plunger
41