PAXDR000 Red Lion Controls, PAXDR000 Datasheet - Page 3

• Manufacturer Part Number: PAXDR000
• Description: AC, Dual Rate, Upgradeable Red
• Manufacturer: Red Lion Controls
• Type: Rate/Totalizerr

Specifications of PAXDR000

• Accuracy: ± (0.01% of Input Signal Frequency)
• Cut Out, Panel: 3.62W x 1.77H Inches
• Dimensions: 3.80W x 1.95H Inches
• Display Digit Height: .56 Inches
• Display Type: LED Adjustable
• Function: Rate/Totalizer
• Input Type: Switch Selectable Pulse
• Keypad Type: 3 Programmable Function (5 Keys Total)
• Number Of Digits: Rate = 5, Totalizer = 8
• Primary Type: Electronic
• Range, Measurement: Rate = 0 to 99999, Totalizer = ±99999999
• Special Features: Programmable Function Keys
• Termination: Cage Clamp
• Voltage, Supply: 85 to 250 VAC
• Lead Free Status / Rohs Status: RoHS Compliant part

1. DISPLAY: 6 digit, 0.56" (14.2 mm) red sunlight readable or standard green
2. POWER:
3. SENSOR POWER: 12 VDC, ±10%, 100 mA max. Short circuit protected
4. KEYPAD: 3 programmable function keys, 5 keys total
5. RATE DISPLAYS:
6. TOTALIZER DISPLAYS:
7. INPUTS A and B: DIP switch selectable to accept pulses from a variety of
M
LED, intensity adjustable.
AC Versions:
DC Versions:
Maximum Display: 5-digits
Display Range: 0 to 99999 (Rate A or B); -9999 to 99999 (Rate C)
Over/Under Range Display: “
Annunciators (displayed in Digit 6):
Display Update Time: Adjustable 0.1 to 99.9 seconds
Maximum Frequency: See Maximum Signal Frequencies Table
Minimum Frequency: 0.01 Hz
Accuracy: ±0.01% of input signal frequency
Maximum Display: 8-digits
Display Range: ±99999999; For values greater than 6 digits, display
Over/Under Range Display: “
Annunciators: A, B and C along left side of display for selected Totalizer.
Maximum Frequency: See Maximum Signal Frequencies Table
sources including switch contacts, TTL outputs, magnetic pickups and all
standard Red Lion sensors.
Logic: Input trigger levels V
Magnetic Pickup:
Dual Count Modes: When any dual count mode is used, then User Inputs 1
AC Power: 85 to 250 VAC, 50/60 Hz, 18 VA
Isolation: 2300 Vrms for 1 min. to all inputs and outputs. (300 V working)
DC Power: 11 to 36 VDC, 14 W
(derate operating temperature to 40 °C if operating <15 VDC and three
AC Power: 24 VAC, ± 10%, 50/60 Hz, 15 VA
Isolation: 500 Vrms for 1 min. to all inputs and outputs (50 V working).
alternates between high order (
Notes:
Current sinking: Internal 7.8 K pull-up to +12 VDC, I
Current sourcing: Internal 3.9 K pull-down, 7.3 mA max. @ 28 VDC,
Filter: Damping capacitor provided for switch contact bounce. Limits
Sensitivity: 200 mV peak
Hysteresis: 100 mV
Input impedance: 3.9 K @ 60 Hz
Maximum input voltage: ±40 V peak, 30 Vrms
and/or 2 will accept the second signal of each signal pair. The user inputs
do not have the Logic/Mag, HI/LO Freq, and Sink/Source input setup
switches. The user inputs are inherently a logic input with no low
frequency filtering. Any mechanical contacts used for these inputs in a
dual count mode must be debounced externally. The user input may only
be selected for sink/source by the User Jumper placement.
1
2
3
4
RATE ONLY (Totalizers A & B Disabled)
Single Rate (A or B)
Dual Rate (A & B)
DUAL RATE WITH
TOTALIZER(S)
Setpoint(s) assigned to an
enabled Totalizer ?
TOTALIZER A or B
OPERATING MODE
frequency listed applies to both Totalizers.
These values apply with or without Rate C Calculation enabled.
See Programming Module 4 for Totalizer Operating Mode descriptions.
Derate listed values by 15% if Totalizer C Calculation is enabled.
If both Totalizers are used with different operating modes, then the lower
ETER
plug-in option cards are installed)
V
input frequency to 50 Hz and input pulse widths to 10 msec. minimum.
MAX
Quadrature x1
Quadrature x2
Quadrature x4
Count x1
Count x2
= 30 VDC.
Maximum Signal Frequencies Table
S
3
PECIFICATIONS
IL


= 1.5 V max.; V
44 KHz
19 KHz
Enabled (A or B)
Single Totalizer

9.5
9.5
9.5
No
14
14
”
”
Maximum Frequency in KHz

prefix) and low order digits.
1
1
- Rate A,
(with or without setpoints)
(with or without setpoints)
Yes
8.5
8.5
8.5
9
5
IH

= 3.75 V min.
- Rate B,
Enabled (A & B)
Both Totalizers
N/A
No
13
10
8
7
MAX

= 1.9 mA.
- Rate C
4
Yes
N/A
8.5
4.5
7
4
2
3
8. USER INPUTS: Three programmable user inputs
9. MEMORY: Nonvolatile E
10. CERTIFICATIONS AND COMPLIANCES:
11. ENVIRONMENTAL CONDITIONS:
12. CONNECTIONS: High compression cage-clamp terminal block
13. CONSTRUCTION: This unit is rated for NEMA 4X/IP65 outdoor use.
14. WEIGHT: 10.1 oz. (286 g)
Max. Continuous Input: 30 VDC
Isolation To Sensor Input Commons: Not isolated
Logic State: Jumper selectable for sink/source logic
Response Time: 6 msec. typical; function dependent. Certain resets, stores
display values when power is removed.
SAFETY
ELECTROMAGNETIC COMPATIBILITY
Emissions and Immunity to EN 61326: Electrical Equipment for Measurement,
Notes:
Operating Temperature Range: 0 to 50 °C (0 to 45 °C with all three plug-in
Storage Temperature Range: -40 to 60 °C
Operating and Storage Humidity: 0 to 85% max. relative humidity non-
Altitude: Up to 2000 meters
Wire Strip Length: 0.3" (7.5 mm)
Wire Gage: 30-14 AWG copper wire
Torque: 4.5 inch-lbs (0.51 N-m) max.
IP20 Touch safe. Installation Category II, Pollution Degree 2. One piece
bezel/case. Flame resistant. Synthetic rubber keypad. Panel gasket and
mounting clip included.
Immunity to Industrial Locations:
Electrostatic discharge
Electromagnetic RF fields EN 61000-4-3
Fast transients (burst)
Surge
RF conducted interference EN 61000-4-6
AC power
Emissions:
Emissions
and inhibits respond within 25 μsec if an edge occurs with the associated
totalizer or within 6 msec if no count edge occurs with the associated
totalizer. These functions include

msec max. After that period, another edge/level may be recognized.
Control and Laboratory use.
1. Criterion A: Normal operation within specified limits.
2. Criterion C: Temporary loss of function where system reset occurs.
Refer to the EMC Installation Guidelines section of the bulletin for
cards installed)
condensing
INPUT STATE
IEC 61010-1, EN 61010-1: Safety requirements for electrical equipment
IP65 Enclosure rating (Face only), IEC 529
IP20 Enclosure rating (Rear of unit), IEC 529
additional information.
Inactive
for measurement, control, and laboratory use, Part 1.
Active
Short interruptions
. Once activated, all functions are latched for 50 msec min. to 100
Voltage dip
5.1 K pull-up to +12 V
SINKING INPUTS
V
V
IN
IN
2
PROM retains all programmable parameters and
< 0.9 VDC
> 3.6 VDC
EN 61000-4-2
EN 61000-4-4
EN 61000-4-5
EN 61000-4-11
EN 55011

,
SOURCING INPUTS
Criterion A
Criterion A
Criterion A
Criterion A
Criterion A
Criterion A
Criterion C
Class A
5.1 K pull-down

V
V
4 kV contact discharge
8 kV air discharge
10 V/m (80 MHz to 1 GHz)
3 V/m (1.4 GHz to 2 GHz)
1 V/m (2 GHz to 2.7 GHz)
2 kV power
1 kV I/O signal
2 kV I/O signal connected
power 1 kV L to L,
signal 1 kV
3 Vrms
0% during 1 cycle
40% during 10/12 cycle
70% during 25/30 cycle
0% during 250/300 cycles
IN
IN
to power
2 kV L to G
> 3.6 VDC
< 0.9 VDC
,

,

, and