LSN-1.5/10-D12H-C Murata Power Solutions Inc, LSN-1.5/10-D12H-C Datasheet - Page 3
![DC/DC TH 10A 12-1.5V H Non-Iso](/photos/38/71/387191/lsn10a-d12_sml.jpg)
LSN-1.5/10-D12H-C
Manufacturer Part Number
LSN-1.5/10-D12H-C
Description
DC/DC TH 10A 12-1.5V H Non-Iso
Manufacturer
Murata Power Solutions Inc
Series
LSNr
Datasheet
1.LSN-510-D12H-C.pdf
(12 pages)
Specifications of LSN-1.5/10-D12H-C
Product
Non-Isolated / POL
Output Power
15 W
Input Voltage Range
10 V to 14 V
Input Voltage (nominal)
12 V
Number Of Outputs
1
Output Voltage (channel 1)
1.5 V
Output Current (channel 1)
10 A
Package / Case Size
SIP
Output Type
Low Voltage Reversed Pin
Output Voltage
1.5 V
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Performance/Functional Specifications
Typical @ T
Input Voltage Range
Input Current:
Input Reflected Ripple Current
Input Filter Type
Overvoltage Protection
Reverse-Polarity Protection
Undervoltage Shutdown
On/Off Control
V
Minimum Loading
Maximum Capacitive Load
V
Ripple/Noise (20MHz BW)
Total Accuracy
Efficiency
Overcurrent Detection and Short-Circuit Protection:
Transient Response (50% load step)
Start-Up Time:
Switching Frequency:
Calculated MTBF
Operating Temperature: (Ambient)
With Derating
Thermal Shutdown
Dimensions
Pin Dimensions/Material
Weight
Flamability Rating
Safety
OUT
OUT
Normal Operating Conditions
Inrush Transient
Standby/Off Mode
Output Short-Circuit Condition
Current-Limiting Detection Point
Short-Circuit Detection Point
SC Protection Technique
Short-Circuit Current
V
1V/1.1V, 1.2V, 1.3 Models
1.5V/1.8V, 2V Models
2.5V, 3.3V, 5V Models
Without Derating (Natural convection)
See Technical Notes and Performance Curves for details.
All models are tested/specified with external 22μF input/output capacitors.These caps
accommodate our test equipment and may not be required to achieve specified performance
in your applications. All models are stable and regulate within spec under no-load conditions.
The On/Off Control (pin 11) is designed to be driven with open-collector logic or the appli-
cation of appropriate voltages (referenced to Common, pins 5 and 6).
Output noise may be further reduced with the installation of additional external output
filtering. See I/O Filtering and Noise Reduction.
MTBF’s are calculated using Telcordia SR-332(Bellcore), ground fixed, T
power, natural convection, +67°C pcb temperature.
IN
Trim Range
to V
Accuracy (50% load)
A
OUT
= +25°C under nominal line voltage and full-load conditions unless noted.
and On/Off to V
Dynamic Characteristics
OUT
Environmental
Physical
Output
Input
UL/cUL/IEC/EN 60950, CSA-C22.2 No. 234
10.8-13.2 Volts (12V nominal)
See Ordering Guide
0.08A
8mA
40mA average
100mAp-p
Capacitive (66μF)
None
None
None
On = open (internal pull-down)
Off = +2.8V to +V
±1.25% maximum
No load
2000μF (low ESR, OSCON)
±10%
See Ordering Guide
3% over line/load/temperature
See Ordering Guide
17 (13-23.5) Amps
98% of V
Hiccup with auto recovery
400mA average
100μsec to ±2% of final value
70msec for V
16msec for V
105/125kHz ±10%
160/177kHz ±10%
200kHz ±7.5%
2.3 -1.8 million hours (1V
+115°C
See Mechanical Specifications
0.03" (0.76mm) round copper alloy with
tin plate over nickel underplate
0.3 ounces (8.5g)
UL94V-0
–40 to +48/64°C (model dependent)
See Derating Curves
2
sec
OUT
www.murata-ps.com
OUT
OUT
set
= 1V
= 1.1V to 5V
IN
(<3mA)
OUT
A
= +25°C, full
to 5V
Single Output, Non-Isolated, 12V
OUT
)
Return Current Paths
The LSN D12 SIP’s are non-isolated DC/DC converters. Their two Common
pins (pins 5 and 6) are connected to each other internally (see Figure 1). To
the extent possible (with the intent of minimizing ground loops), input return
current should be directed through pin 6 (also referred to as –Input or Input
Return), and output return current should be directed through pin 5 (also
referred to as –Output or Output Return). Any on/off control signals applied to
pin 11 (On/Off Control) should be referenced to Common
(specifically pin 6).
I/O Filtering and Noise Reduction
All models in the LSN D12 Series are tested and specified with external
22μF tantalum input and output capacitors. These capacitors are necessary
to accommodate our test equipment and may not be required to achieve?
desired performance in your application. The LSN D12's are designed with
high-quality, high-performance internal I/O caps, and will operate within spec
in most applications with no additional external components.
In particular, the LSN D12's input capacitors are specified for low ESR
and are fully rated to handle the units' input ripple currents. Similarly, the
internal output capacitors are specified for low ESR and full-range frequency
response. As shown in the Performance Curves, removal of the external
22μF tantalum output caps has minimal effect on output noise.
In critical applications, input/output ripple/noise may be further reduced using
filtering techniques, the simplest being the installation of external I/O caps.
External input capacitors serve primarily as energy-storage devices. They
minimize high-frequency variations in input voltage (usually caused by IR
drops in conductors leading to the DC/DC) as the switching converter draws
pulses of current. Input capacitors should be selected for bulk capacitance
(at appropriate frequencies), low ESR, and high rms-ripple-current ratings.
The switching nature of modern DC/DC's requires that the dc input voltage
source have low ac impedance at the frequencies of interest. Highly inductive
source impedances can greatly affect system stability. Your specific system
configuration may necessitate additional considerations.
Output ripple/noise (also referred to as periodic and random deviations or
PARD) may be reduced below specified limits with the installation of addi-
tional external output capacitors. Output capacitors function as true filter
These are stress ratings. Exposure of devices to any of these conditions may adversely
affect long-term reliability. Proper operation under conditions other than those listed in the
Performance/Functional Specifications Table is not implied.
T E C H N I C A L
Input Voltage:
On/Off Control (Pin 11)
Input Reverse-Polarity Protection
Output Overvoltage Protection
Output Current
Storage Temperature
Lead Temperature (soldering, 10 sec.)
Continuous or transient
Technical enquiries email: sales@murata-ps.com, tel:
LSN-10A D12 Models
N O T E S
Absolute Maximum Ratings
IN
, 1-5V
OUT,
10A, DC/DC's in SIP Packages
15 Volts
+V
None
None
Current limited. Devices can
withstand sustained output short
circuits without damage.
–40 to +125°C
+300°C
IN
MDC_LSN10A-D12.B01 Page 3 of 12
+1 508 339 3000