LSN-1.5/10-D12B-C Murata Power Solutions Inc, LSN-1.5/10-D12B-C Datasheet
LSN-1.5/10-D12B-C
Specifications of LSN-1.5/10-D12B-C
Related parts for LSN-1.5/10-D12B-C
LSN-1.5/10-D12B-C Summary of contents
Page 1
... High efficiency enables the LSN D12's to deliver rated output currents of 10 Amps at ambient temperatures to +68°C with 100 lfm air flow. If your new system boards call for three or more supply voltages, check out the economics of on-board 12V distributed power ...
Page 2
... V Trim OUT * Pin 3 (+Sense) removed +Input 11 On/Off Control for "B" suffix models. +Input Technical enquiries email: sales@murata-ps.com, tel: MDC_LSN10A-D12.B01 Page Package (Case, Pinout) B5/B5x, P59 B5/B5x, P59 B5/B5x, P59 B5/B5x, P59 B5/B5x, P59 B5/B5x, P59 B5/B5x, P59 B5/B5x, P59 ...
Page 3
... OUT (specifically pin 6). I/O Filtering and Noise Reduction All models in the LSN D12 Series are tested and specified with external 22μF tantalum input and output capacitors. These capacitors are necessary to accommodate our test equipment and may not be required to achieve? ...
Page 4
... On/Off Control and Power-up Sequencing The On/Off Control pin may be used for remote on/off operation. LSN D12 SIP Series DC/DC's are designed so they are enabled when the control pin is left open (internal pull-down to Common) and disabled when the control pin is pulled high (+2 ...
Page 5
... If the output current exceeds it maximum rating by typically 70% (17 Amps the output voltage drops to less than 98 original value, the LSN D12's internal overcurrent-detection circuitry immediately turns off the converter, which then goes into a "hiccup" mode. While hiccupping, the converter will continuously attempt to restart itself, go into overcurrent, and then shut down ...
Page 6
... Lastly, when LSN D12 SIP's are installed in system boards, they are obvi- ously subject to numerous factors and tolerances not taken into account here. If you are attempting to extract the most current out of these units under demanding temperature conditions, we advise you to monitor the output- inductor temperature to ensure it remains below +110° ...
Page 7
... Typical Performance Curves for LSN D12 SIP Series LSN-1.1/10-D12, LSN-1.2/10-D12, LSN-1.3/10-D12 Efficiency vs. Line Voltage and Load Current 10. 12V 13. Load Current (Amps) LSN-1.5/10-D12 Efficiency vs. Line Voltage and Load Current 10. 12V 13. Load Current (Amps) LSN-1.8/10-D12 Efficiency vs. Line Voltage and Load Current 10. 12V ...
Page 8
... Typical Performance Curves for LSN D12 SIP Series LSN-2/10-D12 Efficiency vs. Line Voltage and Load Current 10. 12V 13. Load Current (Amps) LSN-2.5/10-D12 Efficiency vs. Line Voltage and Load Current 10. 12V 13. Load Current (Amps) LSN-3.3/10-D12 Efficiency vs. Line Voltage and Load Current 10. 12V 13. Load Current (Amps) www ...
Page 9
... Typical Performance Curves for LSN D12 SIP Series LSN-5/10-D12 Efficiency vs. Line Voltage and Load Current 10. 12V 13. Load Current (Amps) LSN-1/10-D12H (Horizontal Mount) Output Current vs. Ambient Temperature (Air flow direction from pin 11 to pin Natural Convection 8 100 lfm 6 200 lfm – Ambient Temperature ( C) ...
Page 10
... Typical Performance Curves for LSN D12 SIP Series Power-Up From 12V 5V/10A 22μ 2000μF OSCON) IN OUT IN OUT 4msec/div Output Ripple Noise (V = 12V 5V, Full Load 22μF) IN OUT OUT 1μsec/div Dynamic Load Response (V = 12V 5V/50 to 100% Load Step OUT IN Channel 2 Channel 1 100μs/div www ...
Page 11
... B and CISPR 22 (EN 55022), Class B. Correlation to other specifications can be supplied upon request. The corresponding emissions plots to FCC and CISPR 22 for model LSN-5/10-D12 appear below. The published EMC test report is based on results with the highest possible output power model and is therefore representative of the whole LSN-D12 series. Contact DATEL’s Applications Engineering Department for more details ...
Page 12
... Reversed pin vertical mounting ("J" suffix) This additional mechanical configuration consists of a low-profile pin header attached to the reverse side of the converter. It allows the LSN series to be mechanically compatible with competitors' "keep out area." Other Options and Modifications Other options include a positive polarity (pull low to disable) on the On/Off Control. Contact DATEL directly to discuss these and other possible modifi ...