IMD10060 Red Lion Controls, IMD10060 Datasheet - Page 2

• Manufacturer Part Number: IMD10060
• Description: IMD VD AC
• Manufacturer: Red Lion Controls

Specifications of IMD10060

• Rohs Compliant: NA

SPECIFICATIONS (Cont’d)
4. INPUT RANGE/RESOLUTION, ACCURACY, INPUT IMPEDANCE
5. PROGRAMMABLE DISPLAY READING RANGE: -99999 to 999999
6. READING RATE: 2.5 readings/second
7. RESPONSE TIME: 2 seconds to settle for step input (increases with
8. TOTALIZER: Front panel button for input/total display select
9. E1-CON AND E2-CON: External remote inputs which allow activation of
10. NORMAL MODE REJECTION: 35 dB @ 50/60 Hz (may be improved
11. COMMON MODE REJECTION: 120 dB, DC to 50/60 Hz
12. ENVIRONMENTAL CONDITIONS:
13. EXCITATION (Optional): 18 VDC @ 60 mA max.
14. SERIAL COMMUNICATIONS (Optional):
15. ALARMS (Optional):
16. ANALOG OUTPUT (Optional):
17. LINEARIZER/PEAK/VALLEY/TARE (Optional):
18. CERTIFICATIONS AND COMPLIANCES:
AND MAXIMUM INPUT LEVEL:
On all current ranges, there is a 0.2 volt DC drop.
Note: Any individual range may be recalibrated (scaled) to 0.025% accuracy
programmable digital filtering)
programmable time-base, scale factor (0.001 to 100.000) and low-end cut-
out. Response Time = 0.2 sec. max.
various functions (reset total, peak indicator mode, trigger mode, etc.).
V
by programmable digital filtering)
Operating Temperature Range: 0 to 50
Storage Temperature Range: -40 to 80
Operating and Storage humidity:
Span Temperature Coeff.:
Zero Temperature Coeff.:
Altitude: Up to 2000 meters
Type: Bi-directional 20 mA current loop, 20 mA source provided on transmit
Baud Rate: programmable 300 to 2400
Maximum address: 99 (Actual number in a single loop is limited by serial
Data Format: 10 bit frame, Odd parity (one start bit, 7 data bit, one odd
Serial Hardware Specifications:
Solid State: Two, isolated, sinking open collector NPN transistors acting in
Relays:
4 to 20 mA: Digital scaling and offsetting within 4 to 20 mA range
0 to 10 VDC: Digital scaling and offsetting within 0 to 10 VDC range
9-segment multiple slope scaling for non-linear inputs. Peak and Valley
recording. Signal re-zero (tare).
EMC EMISSIONS:
EMC IMMUNITY:
IL
with appropriate calibration equipment.
85% max (non-condensing) from 0 to 50
loop. (Powers up to 7 units in a loop with internal current source.)
hardware specifications.)
parity bit, and one stop bit.)
SO - Output Transistor Rating: V
Note: This will allow up to 28 units max. in each loop.
SI - Input Diode Rating: VF = 1.25 V
Note: The compliance voltage rating of the source must be greater than the
parallel with relays. Imax: 100 mA @ V
Type: Form C (2)
Max. Rating: 5 Amps @ 115/240 VAC or 28 VDC (resistive load), 1/8 hp
Relay Life Expectancy: 100,000 cycles at max. rating. (As load level
Accuracy: 0.1% of full scale
Resolution: 12 bits
Compliance Voltage: 10 VDC (500
Accuracy: ±(0.1% of reading +35 mV)
Resolution: 12 bits
Min. Load Resistance: 10 W (1 mA max.)
Meets EN 50081-2: Industrial Environment.
Meets EN 50082-2: Industrial Environment.
= 0.8 V
VOLTAGE
RANGES/RESOLUTION
±2.0000 V/0.1 mVDC
±20.000 V/1 mVDC
±200.00 V/10 mVDC
±300.0 V/100 mVDC
CURRENT
RANGES/RESOLUTION
±200.00 µA/10 nA DC
±2.0000 mA/0.1 µA DC
±20.000 mA/1 µA DC
±200.00 mA/10 µA DC
±2.0000 A/0.1 mA DC
V
sum of the voltage drops around the loop. (Typically a 30 VDC powered
source would be capable of operating between 18 and 22 units in a
loop.)
@ 120 VAC (inductive load).
decreases, life expectancy increases.)
CISPR 11 Radiated and conducted emissions
SAT
= 1 V
MAX
; V
MAX
IH
= 2.0 V
at 20 mA.
ACCURACY % OF
ACCURACY % OF
FULL SCALE
FULL SCALE
MIN
0.025%
0.025%
0.15%
50 ppm/
1 µV/
0.1%
0.1%
0.1%
0.1%
0.1%
0.8%
Volt Meter
; Response Time = 0.2 sec. max.
o
C
MAX
W max. loop impedance)
o
o
C
o
C
TYP
C
o
= 30 VDC,
SAT
C
Current Meter
; 1.5 V
R (ohms)
R (ohms)
80 ppm/
1 MEG
1 MEG
1 MEG
1 MEG
1 µV/
= 1 V. V
100
1 K
1.0
0.1
10
MAX
o
C
o
C
MAX
MAXIMUM INPUT
MAXIMUM INPUT
200 mA DC
20 mA DC
2 mA DC
300 VDC
300 VDC
300 VDC
70 VDC
1 A DC
5 A DC
: 30 VDC.
2
19. CONSTRUCTION: Die-cast metal front bezel that meets NEMA 4/IP65
20. CONNECTION: Removable terminal blocks.
21. WEIGHT: 1.2 lbs. (0.54 Kg)
EXCITATION OPTION
mA) that can be used to power the transducer.
TOTALIZER/LINEARIZER/PEAK/VALLEY/TARE/
E2-CON OPTION
integrator simply totals (adds) input readings with a programmable time base
and scaling coefficient. The integrator/totalizer may be reset via a remote input,
by the front panel or through the serial communications loop. Alarms may be
programmed to trigger from totalizer values, for example to signal total flow
thresholds for batching operations. A programmable low signal level disable
feature completes the integrator/totalizer features. At loss of power to the
indicator, the contents of the totalizer are saved.
to construct linear segments to linearize the input signal. The most common
application would be to interface with square law devices (generally, flow
transducers). A maximum of nine segments are available and using nine
segments for a square law device would reduce linearity errors to 0.35%.
(tare) function. The indicator will record the lowest reading (valley) and the
highest reading (peak), automatically, for later recall. This information is
valuable when monitoring the limits of the process over any length of time
(shifts, days, etc.) since these values are stored at power-down. Optional E2-
CON input pin can be programmed to reset or engage the unit into a peak
reading indicator. Additionally, the peak and valley can be viewed and reset
from the front panel, if so programmed, and viewed and reset through the serial
communication option.
panel. This feature can quickly compensate for small shifts or drifts in the input
signal or to re-zero every operation, such as batching.
ISOLATED ALARM OPTION
terminals. Six of these terminals are for the two Form-C relays and the other
three are for the two open collector transistors, which act in parallel with the
relays. The two alarms are completely independent with programmable values,
hysteresis (deadband), high or low acting, auto or manual reset, triggering from
input or total and they can be programmed to track each other, if desirable. If
the alarms are programmed to latch (manual reset), then they can be reset either
by the front panel or a remote input. The alarms can be set to trigger from either
the integrator/totalizer or the input display, to actuate external alarms, control
valves, etc.
This is useful in alarm set-ups where a pre-warning control activates before a
second alarm shuts off the process when tracking is programmed. Changing the
shut-off trip value (alarm #2) automatically changes the pre-warn value (alarm
#1) an equal amount. Alarm and hysteresis values can be modified through the
optional serial communications to provide automatic control.
ISOLATED SERIAL COMMUNICATIONS OPTION
can connect to a variety of printers, computers, terminals and controllers to suit
many data-polling or automatic operation applications. The indicator responds
to a host of commands, including change alarm value, reset totalizer and
transmit input signal. Two loops are required for all hook-ups; a transmit (out-
going data) loop and a receive (in-coming data) loop. Since the indicator
monitors the receive loop for a busy signal (current interrupted) while
Notes:
1. Unit mounted in a metal panel connected to earth ground (protective
2. One ferrite suppression core (Steward #28-B2025-0A0) placed on the 20
3. Metal bezel of unit connected with ground lead from rear bezel screw to
Refer to the EMC Compliance Installation section of the manual for
requirements for indoor use when properly installed.Installation Category II,
Pollution Degree 2. Case body is black, high impact plastic (panel gasket and
mounting clips included).
The excitation option provides a regulated excitation voltage (18 VDC, 60
The major feature of this option is its integrator/totalizer (accumulator). The
The linearizer feature is a series of programmable scaling points that are used
The other features of this option are peak and valley detection and a re-zero
The re-zero (tare) function can also be controlled externally or by the front
The alarm option consists of an additional printed circuit board with 9
Alarm #1 can be programmed to track Alarm #2 by enabling alarm tracking.
The serial communication option is a half-duplex, two-way 20 mA loop that
earth) with rear cover providing at least 10 dB of shielding effectiveness.
mA serial communications cable at the unit for EMI frequencies above 40
MHz.
metal mounting panel.
additional information.
ENV 50140 - Radio-frequency radiated electromagnetic field
ENV 50141 - Radio-frequency conducted electromagnetic field
EN 61000-4-2 - Electrostatic discharge (ESD)
EN 61000-4-4 - Electrical fast transient/burst (EFT)
a. When units are mounted in a metal panel without a rear cover, the
process signal can vary as much as 2% from the stated accuracy
specification, and the 4 to 20 mA analog output option can vary as
much as 16% from the stated accuracy specification.
3
1
2