453391604 Molex Inc, 453391604 Datasheet
![no-image](/images/manufacturer_photos/0/4/456/molex_inc_sml.jpg)
453391604
Specifications of 453391604
45339-1604
453391604
Related parts for 453391604
453391604 Summary of contents
Page 1
...
Page 2
SMT Receptacle Connector 45339 and 45593 Plug Connector Modules REVISION: ECR/ECN INFORMATION: UCP2006- 1391 EC No: A DATE: 2005/12/13 DOCUMENT NUMBER: SD-45339-001 HANDYLINK™ APPLICATION SPECIFICATION HANDYLINK™ I/O CONNECTORS TITLE: APPLICATION SPECIFICATION HANDYLINK™I/O CONNECTOR SYSTEM CREATED / REVISED BY: M. ...
Page 3
Section 1.0 Scope 2.0 Product Description 3.0 Applicable Documents and Specifications 4.0 Mating and Un-Mating of Connectors 4.1 Recommendations for Mating and Un-Mating 4.2 Mating Alignment Tolerances 5.0 Soldering Process Recommendations 5.1 44828 SMT Receptacle Connector 5.1.1 PCB Layout 5.1.2 ...
Page 4
SCOPE This specification addresses the manufacturing techniques and end-usage considerations for Molex’s 0.8mm pitch HandyLink™ I/O Connectors. The common contact interface used in this family of connectors consists of a flat pad mated to a radiussed edge on a ...
Page 5
MATING AND UN-MATING OF CONNECTORS This section describes the preferred methods for mating and un-mating the HandyLink™ connectors. 4.1 Recommendations for Mating and Un-Mating This connector system utilizes a “passive” latching feature. There is no button to press to ...
Page 6
Mating Alignment Tolerances (continued) 4.2.b 44828 Receptacle to 45560 Cradle Connectors The HandyLink™ receptacle and cradle connectors’ alignment features are manufactured with clearances to allow some axial mating mis-alignment as illustrated in the Figure 2, below: Figure 2. Receptacle ...
Page 7
Clearances Between Mated Parts The HandyLink connectors are designed such that the corresponding ‘front’ faces fully engage and then spring back 0.20mm to the final mated condition. This ‘over-travel clearance’ assures that the components of the passive latching system ...
Page 8
Reflow Profile While the production solder reflow profile is typically established by the customer, based on their specific application, generic reflow in profiles can be found Product Specification PS-44828-001. The profiles are provided for reference purposes only. 5.2.4 Inspection ...
Page 9
MECHANICAL MOUNTING RECOMMENDATIONS 6.1 Mechanical Fasteners and Support 6.1.1 Receptacle Connector Molex recommends that the receptacle connector be mounted within the end-application enclosure such that it is recessed by 1.6 to 2.4mm from the outermost faces and with a ...
Page 10
Figure 3B. Receptacle Connector Recess When Mating with the Plug or Cradle Connectors (units: mm) Wherever possible, the 0.10 maximum clearance condition with the receptacle should be minimized by utilizing a clam-shell style package design. 6.1.2 Plug Connector Module The ...
Page 11
Ingress Protection Ingress protection, as described by IEC 60529 function of the customer’s enclosure. The HandyLink™ Receptacle Connector has been designed to facilitate enclosure design when ingress protection is required. The interfaces between the metal and plastic ...
Page 12
Plug Cable Over-Molding 6.3.1 Wire Soldering This section provides an outline of the recommended plug cable over-molding practices for the 45339 and 45593 plug connector modules. The 45339 connector (a 16-circuit wire termination version) is shown, below, prior to ...
Page 13
REVISION: ECR/ECN INFORMATION: UCP2006- 1391 EC No: A DATE: 2005/12/13 DOCUMENT NUMBER: SD-45339-001 HANDYLINK™ APPLICATION SPECIFICATION Figure 6. Plug Soldering Set-Up NOTE: The wire bundle must be properly supported or clamped as shown, during soldering and handling, to avoid dislodging ...
Page 14
Encapsulation The next step after soldering is to pre-seal or encapsulate the back end of the connector and hold the wires in place using a silicone sealant or a low-pressure Macro-melt polyamide adhesive molding. The sealant will prevent accidental ...
Page 15
Strain Relief Molex strongly recommends the use of a crimp barrel or ferrule over the wire bundle (including ground or drain wire) that also captures the cable jacket and tension member, if used. This will uniformly distribute mechanical loads ...
Page 16
Design Best Practices The information provided so far in this document has been related to the basic usage conditions of the HandyLink™ connectors. The sections that follow contain important information and guidelines for design that apply to specific applications ...
Page 17
Plug Over-Mold Designs Supplemental guide features to align the connectors during mating or un-mating are strongly recommended if any of the following conditions are present great deal of curvature in the end product (such as that illustrated, ...
Page 18
Contouring with a Lip To provide mechanical support for torque out of the axial plane of the connectors, the over-mold must be designed to mimic the outer surfaces of the end product and include a lip such as illustrated ...
Page 19
Supplemental Latching and Alignment Posts Where the mass of the end product is greater than 1000 grams and is subject to sudden accelerations or strong vibrations during use, a cup-style receptacle needs to be considered to adequately protect the ...
Page 20
Supplemental alignment posts must be longer than the protrusion of the plug connector posts from the base surface of the cup-style receptacle. Further, the alignment posts’ centerlines must lie in the same plane as the centerlines of the plug connector ...
Page 21
Cradle Designs o Cup Style The cup or holster style of cradle provides the greatest degree of alignment between mating connectors. Where the end product mass is greater than 1000 grams the use of supplemental alignment posts is recommended. ...
Page 22
Figures 16 and 17 show orthogonal views of showing differences in the position and size of the openings in the cradle casing, and the PCB location for the 45560 and 45593 connectors. Figure 18 shows a chamfer detail applicable to ...
Page 23
Shelf Style To achieve a ‘rocking’ disconnection for the end product from the cradle, a shelf style cradle design may be used under the following conditions: ½ ½ No supplemental guide posts may be used; ½ The end product ...
Page 24
In addition to the differences in the position and size of the openings in the cradle casing, the PCB location for the 45560 and 45593 connectors, and the chamfer detail applicable to 45593 that is shown in Figures 16 thru ...
Page 25
REVISION: ECR/ECN INFORMATION: UCP2006- 1391 EC No: A DATE: 2005/12/13 DOCUMENT NUMBER: SD-45339-001 HANDYLINK™ APPLICATION SPECIFICATION Rocking Direction NOTE: Orientation of the receptacle connector and the plug or cradle connector must correspond to that shown for good operation of a ...
Page 26
Electrical Recommendations 7.1 Power Considerations Please see the Product Specification, PS-44828-001, for the nominal electrical specifications. For applications where the sustained electrical power usage requirements exceed the limits stated in the product specification, the use of multiple circuits is ...