CS1W-CN713 Omron, CS1W-CN713 Datasheet - Page 70

• Manufacturer Part Number: CS1W-CN713
• Description: "CABLE CS1 EXP I/O,70cm"
• Manufacturer: Omron

Specifications of CS1W-CN713

• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Other Memory Specifications
Function Specifications
48
Unit Specifications
Memory Cassette
(EEPROM or flash
memory)
Trace memory
Macro instructions Subroutines called by instructions containing arguments.
Constant cycle
time
Cycle time
monitoring
I/O refreshing
I/O memory
holding when
changing
operating modes
Load OFF
User-customized
DIP switch setting
Mode setting at
power-up
Debugging
Online editing
Program
protection
Error check
Error log
Serial
communications
ports
Serial Communications Modes
Item
Item
1 to 9,999 ms (Unit: 1 ms)
When the cycle time exceeds 100 ms, the Cycle Time Over Flag turns ON, and operation continues.
(A setting can be made in the PC Setup so that this error is not generated.)
When the cycle time exceeds the cycle monitor time, operation is stopped.
Cycle monitor time settings: 0 to 990 ms in 10-ms units, 0 to 9,990 ms in 100-ms units, 0 to 99 s in
1-s units.
Note The maximum and current values of the cycle time are stored in the AR area.
Cyclic refreshing, refreshing by IORF(097), direct output refreshing (set in the PC Setup), interrupt
input refreshing. (The inputs that are refreshed can be set separately for input interrupts, high-speed
counter interrupts, and interval timer interrupts in the PC Setup.)
Depends on the ON/OFF status of the I/O Hold Bit (SR 25212).
All outputs on Output Units can be turned OFF when the CPU Unit is operating in RUN, MONITOR, or
PROGRAM mode. (Used for stopping output in emergencies, for debugging, etc.)
A pin setting on the DIP switch on the front of the CPU Unit is stored in AR 0712. This setting can be
used as an ON/OFF condition (e.g., to switch between trial operation and actual operation).
Possible
Control set/reset, differential monitoring, data tracing (scheduled, each cycle, or when instruction is
executed).
User programs can be overwritten in program-block units when the CPU Unit is in MONITOR mode.
With the CX-Programmer, more than one program block can be edited at the same time.
Write-protection of user program, data memory (DM 6144 to DM 6655: read-only DM), and PC Setup
(DM 6600 to DM 6655): Set using pin 1 on the DIP switch.
FALS(07) instructions.)
Note It is possible to stop operation using user-programmed instructions for fatal errors.
User-defined error logs can be created in specific bits (logging) when using user-programmed
instructions for non-fatal errors.
error code, error details, and the time the error occurred.
Built-in peripheral port: Programming Device (including Programming Console) connections, Host
Links, no-protocol communications
Built-in RS-232C port: Programming Device (excluding Programming Console) connections, Host
Links, no-protocol communications, NT Links (1:1 mode), 1:1 Data LInks
RS-232C port and RS-422A/485 port on Serial Communications Board (sold separately):
Programming Device (excluding Programming Console) connections, Host Links, no-protocol
communications, NT Links (1:1 mode, 1:N mode), 1:1 Data LInks, protocol macros
User-defined errors (i.e., user can define fatal errors and non-fatal errors using the FAL(06) and
Up to 10 errors (including user-defined errors) are stored in the error log. Information includes the
Mounted from the front of the CPU Unit. Memory Cassettes are used to store and read the
user’s program, DM (read-only DM and PC Setup), and expansion instruction information as
one block. It is possible to set the CPU Unit so that when power is turned ON, data stored in
the Memory Cassette (user’s program, DM, expansion instruction information) is automatically
sent to the CPU Unit (auto-boot). Two-way transfer and comparison of data between the CPU
Unit and Memory Cassette are possible using AR area control bits.
1,024 words (trace comparison data: 12 points, 3 words)
Specification
CPU Unit built-in ports
Built-in
peripheral port
Details
Built-in RS-232C
port
Serial
Communications
Board ports
Section 2-1