PAXS0000 Red Lion Controls, PAXS0000 Datasheet - Page 20

• Manufacturer Part Number: PAXS0000
• Description: Strain Gauge Meter
• Manufacturer: Red Lion Controls
• Type: Strain Gager

Specifications of PAXS0000

• No. Of Digits / Alpha: 5
• Meter Function: DC Millivoltmeter
• Meter Range: ± 24mV To ± 240mV
• Digit Height: 14.2mm
• Power Consumption: 15VA
• Operating Temperature Range: 0°C To +50°C
• Supply Voltage Ac, Min: 85V
• Accuracy: 0.07% of Reading +4 µV/+40 µV
• Brand/series: PAX
• Common Mode Rejection Ratio: 80
• Connection Type: 2-Wire (Single-Ended), 4-Wire Bridge (Differential)
• Cut Out, Panel: 1⁄8 DIN
• Dimensions: 4.2" L × 3.8" W × 1.95" H
• Display Digit Height: 0.56 "
• Display Resolution: 1 μV/10 μV
• Display Type: LED
• Function: Strain Gage
• Humidity: 0 to 85% (Max.)
• Impedance: 100 Megohms
• Input Type: Strain Gage
• Length, Stripping: 0.3 in.
• Memory Type: Nonvolatile EEPROM
• Number Of Digits: 5
• Primary Type: Electronic
• Range, Measurement: ±24/±240 mVDC
• Resolution: 16 bit
• Special Features: Programmable Function Keys
• Standards: UL Listed, CE Marked
• Temperature Coefficient: 20 ppm⁄°C (Max.)
• Temperature, Operating: 0 to +50 °C
• Termination: Cage Clamp
• Torque: 4.5 inch-lbs (Max.)
• Voltage, Input: 85 to 250 VAC
• Voltage, Supply: 85 to 250 VAC
• Character Size: 0.56"
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

"
delay time, the meter will capture that display value as the new MAX reading.
A delay time helps to avoid false captures of sudden short spikes.
"
time, the meter will capture that display value as the new MIN reading. A delay
time helps to avoid false captures of sudden short spikes.
"
updates/second, the internal re-zero compensation is disabled, allowing for the
fastest possible output response.
"
"
Drift may be caused by changes in the transducers or electronics, or
accumulation of material on weight systems.
band for a period of time equal to the tracking delay time. When these
conditions are met, the meter re-zeroes the readout. After the re-zero operation,
the meter resets and continues to auto-zero track.
drift, but small enough to not interfere with small process inputs.
This avoids false tracking at the start of the filling operation.
5.4 MODULE 4 - S
?:+86
PAXS: AUTO-ZERO TRACKING
PAXS: AUTO-ZERO BAND
FA86
When the Input Display is above the present MAX value for the entered
,)86
When the Input Display is below the present MIN value for the entered delay
This parameter determines the rate of display update. When set to 20
"686
"68<
The meter can be programmed to automatically compensate for zero drift.
Auto-zero tracking operates when the readout remains within the tracking
The auto-zero tracking band should be set large enough to track normal zero
For filling operations, the fill rate must exceed the auto-zero tracking rate.
Fill Rate
Auto-zero tracking is disabled by setting the auto-zero tracking parameter = 0.
-. - /
-. -
-. -
#
#
#
#
#
/
-
tracking band
tracking time
MAX CAPTURE DELAY TIME*
MIN CAPTURE DELAY TIME*
DISPLAY UPDATE RATE*
3
3
-
to
-. -
-. -
to
H-@!
/!-
to
to
/
0/J!. -
0/J!. -
sec.
!
sec.
sec.
3-
ECONDARY
/-
updates/sec.
PARAMETER MENU
F
UNCTION
20
"
which can be installed in to the meter’s bezel display assembly. The backlight
for these custom units is activated by this parameter.
"
desired, this parameter can be skipped. The Display Offset Value is the
difference from the Absolute (gross) Display value to the Relative (net) Display
value for the same input level. The meter will automatically update this Display
Offset Value after each Zero Display. The Display Offset Value can be directly
keyed-in to intentionally add or remove display offset. See Relative / Absolute
Display and Zero Display explanations in Module 2.
"
the ice point compensation is on. If using external compensation, set this
parameter to off. In this case, use copper leads from the external compensation
point to the meter. If using Custom TC range, the ice point compensation can
be adjusted by a value in Module 1 when this is yes.
*
<8,A6
)>>:6
PAXT: ICE POINT COMPENSATION*
The Units Label Kit Accessory contains a sheet of custom unit overlays
This parameter does not apply for the PAXT.
Unless a Zero Display was performed or an offset from Module 1 scaling is
This parameter turns the internal ice point compensation on or off. Normally,
Factory Setting can be used without affecting basic start-up.
A(&
)>>
-. - -
)$
#
#
#
P
ARAMETERS
UNITS LABEL BACKLIGHT*
DISPLAY OFFSET VALUE*
83@@@@
)$
)$
to
)>>
3@@@@
)>>
(
5"6$3
)