PAXD0000 Red Lion Controls, PAXD0000 Datasheet - Page 21

• Manufacturer Part Number: PAXD0000
• Description: Multifunction Meter
• Manufacturer: Red Lion Controls
• Type: Ammeter/Voltager

Specifications of PAXD0000

• No. Of Digits / Alpha: 5
• Meter Range: ± 200uA To ± 2A / ± 200mV To ± 300V / 100ohm To 10kohm
• Digit Height: 14.2mm
• Power Consumption: 15VA
• Operating Temperature Range: 0°C To +50°C
• Supply Voltage Ac, Min: 85V
• Brand/series: PAX
• Connection Type: Cage-Clamp
• Cut Out, Panel: 1⁄8 DIN
• Dimensions: 4.2" L × 3.8" W × 1.95" H
• Display Digit Height: 0.56 "
• Display Resolution: 10 nA to 0.1 mA/10 μV to 10 mV
• Display Type: LED
• Function: Ammeter/Voltage
• Meter Type: Panel
• Number Of Digits: 6
• Primary Type: Electronic
• Range, Measurement: ±200 μADC to ±2 ADC/±200 mVDC to ±300 VDC
• Special Features: Programmable Function Keys
• Standards: CE Marked, cUL Recognized
• Termination: Cage Clamp
• Voltage, Input: 85 to 250 VAC
• Voltage, Supply: 85 to 250 VAC
• Character Size: 0.56"
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

two modes. The first is using a time base. This can be used to compute a time-
temperature product. The second is through a user input or function key
programmed for Batch (one time add on demand). This can be used to provide
a readout of temperature integration, useful in curing and sterilization
applications. If the Totalizer is not needed, its display can be locked-out and this
module can be skipped during programming.
"
(
"
accumulated through a user input programmed for Batch, then this parameter
does not apply.
"
and engineering units as the Input Display. In these cases, the Totalizer Scale
Factor is 1.000. The Totalizer Scale Factor can be used to scale the Totalizer to
a different value than the Input Display. Common possibilities are:
Batch, then this parameter does not apply.
"
the value programmed.
"
parameter to reset.
5.5 MODULE 5 - T
?&(+6
6<'D&
:(>"(
,5726
?&(+6
*
The totalizer accumulates (integrates) the Input Display value using one of
For most applications, this matches the Input Display Decimal Point
This is the time base used in Totalizer accumulations. If the Totalizer is being
For most applications, the Totalizer reflects the same decimal point location
1. Changing decimal point location (example tenths to whole)
2. Average over a controlled time frame.
Details on calculating the scale factor are shown later.
If the Totalizer is being accumulated through a user input programmed for
A low cut value disables Totalizer when the Input Display value falls below
L8*L
The Totalizer can be reset to zero on each meter power-up by setting this
Factory Setting can be used without affecting basic start-up.
8 3@@. @ @
3. - --
). If a different location is desired, refer to Totalizer Scale Factor.
-. - -
K
A$
$)
#
#
#
#
#
TOTALIZER POWER UP RESET*
TOTALIZER LOW CUT VALUE*
TOTALIZER DECIMAL POINT*
TOTALIZER SCALE FACTOR*
D&(
K K
A$
TOTALIZER TIME BASE
83@@@@
rSt
-. - -3
- minutes (÷ 60)
NO
-
0
seconds (÷ 1)
to
Do not reset buffer
Reset buffer
to
%!. - --
0. 0
@@@@@
0. 0 0
M52#
?'9
OTALIZER
-
-
days (÷ 86400)
0. 0 00 0. 0 000
hours (÷ 3600)
PARAMETER MENU
(I
NTEGRATOR
21
TOTALIZER HIGH ORDER DISPLAY
this case, the meter continues to totalize up to a 9 digit value. The high order 4
digits and the low order 5 digits of the total are displayed alternately. The letter
“
Totalizer will show “E . . .” and will stop.
TOTALIZER BATCHING
function key is programmed for store batch (
input or function key is activated, the Input Display reading is one time added
to the Totalizer (batch). The Totalizer retains a running sum of each batch
operation until the Totalizer is reset. This is useful in weighing operations, when
the value to be added is not based on time but after a filling event.
TOTALIZER USING TIME BASE
Example: The input reading is at a constant rate of 10.0 gallons per minute. The
TOTALIZER SCALE FACTOR CALCULATION EXAMPLES
Input Display Decimal Point (
multiplied by a power of ten.
Totalizer Time Base is divided by the given time period expressed in the same
timing units.
would be 0.250. To achieve a controlled time frame, connect an external timer
to a user input programmed for
and the stopping (hold) of the totalizer.
Totalizer accumulates as defined by:
M
” denotes the high order display. When the total exceeds a 9 digit value, the
When the total exceeds 5 digits, the front panel annunciator TOT flashes. In
The Totalizer Time Base and scale factor are overridden when a user input or
Where:
Totalizer is used to determine how many gallons in tenths has flowed.
Because the Input Display and Totalizer are both in tenths of gallons, the
Totalizer Scale Factor is 1. With gallons per minute, the Totalizer Time Base
is minutes (60). By placing these values in the equation, the Totalizer will
accumulate every second as follows:
10.0 x 1.000 = 0.1667 gallon accumulates each second
This results in:
1. When changing the Totalizer Decimal Point (
Example:
Input (
2. To obtain an average reading within a controlled time frame, the selected
Example: Average temperature per hour in a 4 hour period, the scale factor
10.0 gallons accumulates each minute
600.0 gallons accumulates each hour
Totalizer
?&(+6
x1000
x100
Input Display - the present input reading
Totalizer Scale Factor - 0.001 to 65.000
Totalizer Time Base - (the division factor of
x10
0.0
60
0
?&(+6
(x = Totalizer display is round by tens or hundreds)
Factor
0.001
Scale
0.01
0.1
10
1
) = 0
Input Display x Totalizer Scale Factor
) P
Input (
ARAMETERS
Totalizer
Totalizer Time Base
?&(+6
x100
0.00
x10
0.0
?&(+6
0
#656/
?&(+6
), the required Totalizer Scale Factor is
Factor
0.001
. The timer will control the start (reset)
Scale
0.01
0.1
10
1
) = 0.0
<"6
). In this mode, when the user
6<":&
Input (
?&(+6
Totalizer
?&(+6
0.000
0.00
x10
0.0
(
0
)
?&(+6
7"8*8
) location from the
Factor
0.001
Scale
0.01
) = 0.00
0.1
10
1
)