PAXCDC40 Red Lion Controls, PAXCDC40 Datasheet - Page 3
![Modbus Communications Network Interface Card](/photos/21/37/213702/4551881_sml.jpg)
PAXCDC40
Manufacturer Part Number
PAXCDC40
Description
Modbus Communications Network Interface Card
Manufacturer
Red Lion Controls
Specifications of PAXCDC40
Accessory Type
Modbus Communications Network Interface Card
Brand/series
PAX Series
Card Type
Extended Modbus Communications Card
Data Rate
7⁄8 Bits
Standards
cULus Listed, CSA Certified and CE Marked
Voltage, Working
50 V
Pax Label Kit
189 Different Engineering Units, Labels Inserted Inside the Unit
For Use With
Red Lion PAX Digital Input Panel Meters
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
1. DISPLAY: 6 digit, 0.56" (14.2 mm) red sunlight readable or standard green
2. POWER:
3. SENSOR POWER: 12 VDC, ±10%, 100 mA max. Short circuit protected
4. KEYPAD: 3 programmable function keys, 5 keys total
5. USER INPUTS: Three programmable user inputs
6. MEMORY: Nonvolatile E
7. CERTIFICATIONS AND COMPLIANCES:
G
LED
AC Versions:
DC Versions:
Max. Continuous Input: 30 VDC
Isolation To Sensor Input Commons: Not isolated
Logic State: Jumper selectable for sink/source logic
INPUT STATE
Response Time: 6 msec. typical; function dependent. Certain resets, stores
display values.
SAFETY
Inactive
AC Power: 85 to 250 VAC, 50/60 Hz, 18 VA
Isolation: 2300 Vrms for 1 min. to all inputs and outputs. (300 V working)
DC Power: 11 to 36 VDC, 14 W
(derate operating temperature to 40° C if operating <15 VDC and three
AC Power: 24 VAC, ± 10%, 50/60 Hz, 15 VA
Isolation: 500 Vrms for 1 min. to all inputs and outputs (50 V working).
and inhibits respond within 25 μsec if an edge occurs with the associated
counter or within 6 msec if no count edge occurs with the associated
counter. These functions include
50 msec min. to 100 msec max. After that period, another edge/level may
be recognized.
UL Recognized Component, File #E179259, UL61010A-1, CSA C22.2
No. 61010-1
UL Listed, File #E137808, UL508, CSA C22.2 No. 14-M95
Type 4X Enclosure rating (Face only), UL50
IECEE CB Scheme Test Report #04ME11209-20041018
Active
ENERAL
plug-in option cards are installed)
Recognized to U.S. and Canadian requirements under the Component
Recognition Program of Underwriters Laboratories, Inc.
LISTED by Und. Lab. Inc. to U.S. and Canadian safety standards
IEC 61010-1, EN 61010-1: Safety requirements for electrical equipment
IP65 Enclosure rating (Face only), IEC 529
IP20 Enclosure rating (Rear of unit), IEC 529
Issued by Underwriters Laboratories, Inc.
for measurement, control, and laboratory use, Part 1.
,
, and
5.1 K pull-up to +12 V
SINKING INPUTS
V
V
IN
IN
< 0.9 VDC
> 3.6 VDC
2
PROM retains all programmable parameters and
M
. Once activated, all functions are latched for
ETER
SOURCING INPUTS
5.1 K pull-down
,
V
V
IN
IN
> 3.6 VDC
< 0.9 VDC
S
,
PECIFICATIONS
,
,
3
ELECTROMAGNETIC COMPATIBILITY
8. ENVIRONMENTAL CONDITIONS:
9. CONNECTIONS: High compression cage-clamp terminal block
10. CONSTRUCTION: This unit is rated for NEMA 4X/IP65 outdoor use.
11. WEIGHT: 10.1 oz. (286 g)
Emissions and Immunity to EN 61326:2006: Electrical Equipment for
Notes:
Refer to EMC Installation Guidelines section of the bulletin for additional
Operating Temperature Range: 0 to 50°C (0 to 45°C with all three plug-in
Storage Temperature Range: -40 to 60°C
Operating and Storage Humidity: 0 to 85% max. relative humidity non-
Vibration According to IEC 68-2-6: Operational 5 to 150 Hz, in X, Y, Z
Shock According to IEC 68-2-27: Operational 25 g (10 g relay), 11 msec in 3
Altitude: Up to 2000 meters
Wire Strip Length: 0.3" (7.5 mm)
Wire Gage: 30-14 AWG copper wire
Torque: 4.5 inch-lbs (0.51 N-m) max.
IP20 Touch safe. Installation Category II, Pollution Degree 2. One piece
bezel/case. Flame resistant. Synthetic rubber keypad. Panel gasket and
mounting clip included.
Immunity to Industrial Locations:
Electrostatic discharge
Electromagnetic RF fields EN 61000-4-3
Fast transients (burst)
Surge
RF conducted interference EN 61000-4-6
AC power
Emissions:
Emissions
Measurement, Control and Laboratory use.
1. Criterion A: Normal operation within specified limits.
2. Criterion C: Temporary loss of function where system reset occurs.
information.
cards installed)
condensing
direction for 1.5 hours, 2 g.
directions.
Short interruptions
Voltage dip
EN 61000-4-2
EN 61000-4-4
EN 61000-4-5
EN 61000-4-11
EN 55011
power
signal
Criterion A
Criterion A
Criterion A
Criterion A
Criterion A
Criterion A
Criterion C
Class A
4 kV contact discharge
8 kV air discharge
10 V/m (80 MHz to 1 GHz)
3 V/m (1.4 GHz to 2 GHz)
1 V/m (2 GHz to 2.7 GHz)
2 kV power
1 kV I/O signal
2 kV I/O signal connected
1 kV L to L, 2 kV L to G
1 kV
3 Vrms
0% during 1 cycle
40% during 10/12 cycle
70% during 25/30 cycle
0% during 250/300 cycles
to power