PAXCDC40 Red Lion Controls, PAXCDC40 Datasheet - Page 17
![Modbus Communications Network Interface Card](/photos/21/37/213702/4551881_sml.jpg)
PAXCDC40
Manufacturer Part Number
PAXCDC40
Description
Modbus Communications Network Interface Card
Manufacturer
Red Lion Controls
Specifications of PAXCDC40
Accessory Type
Modbus Communications Network Interface Card
Brand/series
PAX Series
Card Type
Extended Modbus Communications Card
Data Rate
7⁄8 Bits
Standards
cULus Listed, CSA Certified and CE Marked
Voltage, Working
50 V
Pax Label Kit
189 Different Engineering Units, Labels Inserted Inside the Unit
For Use With
Red Lion PAX Digital Input Panel Meters
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Shaded areas are model dependent.
Program lock-out.
by repeatedly pressing the DSP key. An annunciator indicates the display being
shown. These displays can be locked from being visible. It is recommended that
the display be set to
modified. This Programming Mode can be locked with a security code and/or
user input. When locked and the PAR key is pressed, the meter enters a Quick
Programming Mode. In this mode, setpoint, count load and scale factor values
can still be read and/or changed per the selections below. The Display Intensity
Level () parameter also appears whenever Quick Programming Mode is
enabled, and the security code is greater than zero.
6.3 MODULE 3 - D
These displays can be programmed for
Module 3 is the programming for Display lock-out and “Full” and “Quick”
When in the Display Mode, the available displays can be read consecutively
“Full” Programming Mode permits all parameters to be viewed and
SELECTION
x = Counter A , Counter B, and then Counter C
n = Setpoints 1 to 4
PAR
Throughout this document, Programming Mode (without Quick in front) always refers to “Full” Programming (all meter parameters are accessible).
SECURITY
Counter x
x
3-LOC
Lock-out
SELECTION
Display
CODE
>0
>0
>0
COUNTER A B C DISPLAY LOCK-OUT *
0
0
0
CNt
MAX. MIN. DISPLAY LOCK-OUT *
DESCRIPTION
Visible but not changeable in Quick Programming Mode
Visible and changeable in Quick Programming Mode
Not visible in Quick Programming Mode
RATE DISPLAY LOCK-OUT *
CONFIGURED
USER INPUT
not
not
DESCRIPTION
Visible in Display Mode
Not visible in Display Mode
when the corresponding function is not used.
Rate Display
Lock-out
rAtE
USER INPUT
Not Active
Not Active
————
————
STATE
Active
Active
Max Display
Lock-out
or
HI
Quick Programming w/Display Intensity
Quick Programming w/Display Intensity
.
ISPLAY AND
Quick Programming
“Full” Programming
“Full” Programming
“Full” Programming
Min Display
PROGRAMMING MODE ACCESS
WHEN PAR KEY IS
Lock-out
PARAMETER MENU
PRESSED
LO
P
Setpoint 1-4
ARAMETERS
Access
17
SP-n
P
following table). Accessible only with the Setpoint Plug-in card installed.
ROGRAM
COUNT LOAD A B C ACCESS LOCK-OUT *
SCALE FACTOR A B C ACCESS LOCK-OUT *
access the “Full” Programming Mode. Access will only be allowed after entering
a matching security code or universal code of
would not have to be configured for Program Lock-out. However, this lock-out is
overridden by an inactive user input configured for Program Lock-out.
*
The setpoint displays can be programmed for
Factory Setting can be used without affecting basic start-up.
These displays can be programmed for
The Scale Factor values can be programmed for
Entry of a non-zero value will cause the prompt
“FULL” PROGRAMMING MODE ACCESS
Immediate access.
After Quick Programming with correct code # at
After Quick Programming with correct code # at
Immediate access.
No access
Immediate access.
Count Load
x
Counter x
Access
CNtLd
Shaded areas represent program access that is model dependent.
SETPOINT 1 to 4 ACCESS LOCK-OUT *
L
(
OCK
SECURITY CODE *
x
Factor x
SCFAC
to
Access
Scale
-
OUT
)
Security
,
COdE
. With this lock-out, a user input
Code
, or
,
to appear when trying to
,
prompt.
prompt.
Pro
, or
.
, or
.
(See the