EDT1411-NTC-2307 CAL CONTROLS, EDT1411-NTC-2307 Datasheet - Page 2

• Manufacturer Part Number: EDT1411-NTC-2307
• Description: THERMOSTAT, NTC, 2RELAY, 230VAC
• Manufacturer: CAL CONTROLS

Specifications of EDT1411-NTC-2307

• Thermocouple Type: NTC
• Operating Temperature Max: 50°C
• Operating Temperature Min: 0°C
• Output Voltage Max: 250VAC
• Accuracy: ± 1°C
• Approval Bodies: CE
• Approval Category: EN61326-1
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

If both
FAHRENHEIT
LED
1000
-22.0
R.lol
R.uPl
R.off
R.Hys
Unit
DrES
SonD
CAL
°F
RE
keys are pressed and held for 3 seconds,
programming mode is entered.
DEFROST
While holding
the value can be adjusted.
LED
Process
Value
Type of buzzer
sound.
The lower limit
of the setpoint.
The upper limit
of the setpoint.
The offset value
for the refrigeration.
Switch hysteresis
for compressor.
Temperature unit
Display resolution
COMPRESSOR
LED
°C
SET
EDT1411
-30.0
key COMPRESSOR setpoint value appears and by using
Programming Mode
Displayed process value in the run mode, parameter name or value in programming mode.
When held down for 3 second in the run mode, manual defrost starts. After the specified time with
specified time ends. Used for selecting menu and increasing setpoint value of the parameters in the programming mode and for increasing the setpoint value in the run mode When held down for a few
seconds, the change rate accelerates.
When held down for 3 second in the run mode continuous mode starts. After the specified time with
specified time ends. Used for selecting parameters and decreasing the setp
change rate accelerates.
Used for adjusting the value of the setpoint in the run mode and for adjusting the selected parameter in the programming mode. While holding
using
Run Mode
C.pon
C.Fos
C.Con
C.ppn
C.ppF
CP
-29.9
and
Delay time for the compressor
after power is on.
Delay time required for
the compressor to restart
following a stop.
Continuous-on mode duration
for the compressor.
on time for the compressor
output in the case of
probe failure.
oFF time for the compressor
output in the case of
probe failure.
keys the value can be adjusted.
-30.0
If both
and
keys are pressed,
D.int
D.dsp
D.Pon
D.dPo
D.dur
D.drE
run mode is entered.
DE
keys
Defrosting duration.
Interval between
defrost cycles.
Display configuration
during defrost
Delay time for display
real temperature after
defrost is over.
Defrosting after
power is on.
Delay time for defrosting
after power is on.
oint value
2/3
in the programming mode and for decreasing the setpoint value in the run mode When held down for a few seconds, the
D.dur
C.Con
*Note:
Error Messages
parameter manual defrost finishes. When held down for 3 second manual defrost finishes before the
parameter this mode finishes. When held down for 3 second continuous mode finishes before the
Psc
Pfa
23.5
A.lol
A.uPl
A.dFl
A.HYS
A.Set
A.dpo
Al
To stop warning tone, press any key.
Means, thermostat probe is short circuit or temperature value is
higher than the scale .
Means, thermostat probe is broken or temperature value is
lower than the scale .
If process value flashes and warning tone sounds, means,
measured value exceeds the adjusted alarm limit.
Limit for
lower alarm level.
Limit for
upper alarm level.
Time delay to display
alarm message after
alarm is on.
Switch hysteresis
for alarm.
Alarm configuration
Time delay to display
alarm message after
power is on.
key, setpoint value of the selected parameter appears and by
A. Cp
A. de
A.rE.S.
S.Cod
A. re
A. al
SE
-
-
-
-
.
.
Access code for security menu.
This parameter should be
Security parameter
for refrigeration menu
Security parameter
for menu of compressor control
Security parameter
for menu of defrost control
Security parameter
for menu of alarm control
Security parameter
for refrigeration setpoint value
321 .
EDT1411-E-06