E5CK-AA1302 Omron, E5CK-AA1302 Datasheet - Page 8
![Process Controller](/photos/21/27/212780/3774311_sml.jpg)
E5CK-AA1302
Manufacturer Part Number
E5CK-AA1302
Description
Process Controller
Manufacturer
Omron
Datasheet
1.E53-C4DR4.pdf
(11 pages)
Specifications of E5CK-AA1302
Operating Temperature Max
55°C
Operating Temperature Min
-10°C
Temperature Accuracy ±
0.3%
Supply Voltage Ac, Min
100VAC
Supply Voltage Ac, Max
240VAC
Signal Input Type
4-20mA Current
Thermocouple Type
J, K, T, E, L, U, N, R, S, B, W, PLII
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Safety Precautions for All Temperature Controllers
Refer to the precautions of individual product for more specific details.
The following products contain lithium batteries. Do not
disassemble, deform under pressure, heat to over
100°C, or incinerate these products. The lithium bat-
tery may ignite or explode. Applicable models: E5ZE,
E5LD, and E5LC.
Do not touch any of the terminals while the power is
being supplied. Doing so may result in electric shock.
Do not allow pieces of metal or wire cuttings to get
inside the Temperature Controller. Doing so may
result in electric shock, fire, or malfunction.
Do not attempt to disassemble, repair, or modify the
Temperature Controller. Any attempt to do so may
result in electric shock, fire, or malfunction.
Do not use the Temperature Controller in locations
subject to flammable or explosive gases. Doing so
may result in an explosion.
The switching capacity and switching conditions will
significantly affect the longevity of the output relays.
Use the Temperature Controller within the rated load,
and do not use the Temperature Controller beyond the
number of operations specified under electrical life.
Using the Temperature Controller beyond its electrical
life may result in contact welding or burning.
Use Temperature Controller settings that are
appropriate for the controlled system. Failure to do so
may cause unexpected operation resulting in damage
to equipment or personal injury
Prepare a circuit with an overheating prevention alarm
and implement other safety measures to ensure safe
operation in the event of a malfunction. Loss of
operational control due to malfunction may result in a
serious accident.
Tighten the terminal screws to the following
torque:
Failure to tighten terminal screws to the correct torque
may result in fire or malfunction.
Make sure there will be no adverse affects from the
device connected to the Temperature Controller
before using the hardware test mode. Devices
connected to the Temperature Controller may reach a
dangerous state during the test.
M3.5 screws: 0.74 to 0.90 N·m
M3 screws: 0.40 to 0.56 N·m
E5GN: Terminals 1 to 6: 0.23 to 0.25 N·m
Terminals 7 to 9: 0.12 to 0.14 N·m
http://www.ia.omron.com/
Warning
Caution
1. Do not use the Temperature Controller in the following locations:
2. Use and store the Temperature Controller within the rated
3. Allow enough space around the Temperature Controller to
4. Be sure to wire properly with correct polarity of terminals.
5. To wire the E5AN, E5EN, or E5CN using crimp terminals, use
6. When wiring the E5GN, use a cable gauge of AWG24
7. After wiring is completed, do not pull on or bend a terminal
8. Do not connect anything to unused terminals.
9. Make sure that the power supply voltages and loads are
10. To avoid inductive noise, keep the wiring for the Temperature
11. Make sure that the rated voltage is attained within two sec-
12. Allow at least 30 seconds for the Temperature Controller to
13. When using self-tuning, turn ON power for the load (e.g.,
• Locations exposed to radiated heat from heating devices
• Locations subject to exposure to water or oil
• Locations subject to direct sunlight
• Locations subject to dust or corrosive gases (in particular,
• Locations subject to severe changes in temperature
• Locations subject to icing or condensation
• Locations subject to excessive shock or vibration
temperature or humidity range specified for each model.
When two or more Temperature Controllers are mounted hor-
izontally close to each other or vertically next to one another,
the internal temperature will increase due to the heat they
radiate and the service life of the products will decrease. In
such cases, forced cooling by fans or other means of air ven-
tilation will be required to cool down the Temperature Con-
trollers.
ensure proper heat dissipation. Do no block the ventilating
holes.
crimp terminals designed for M3.5 screws and with a width of
7.2 mm max.
(0.205 mm
use a cable gauge of AWG28 (0.081 mm
(0.326 mm
ing part to be inserted into terminals must be 5 to 6 mm.
block lead wire with a force of 30 N or higher.
within specification and rating ranges before using the Tem-
perature Controller.
Controller's terminal board away from power cables carrying
high voltages or large currents. Also, do not wire power lines
together with or parallel to Temperature Controller wiring.
Using shielded cables to separate pipes and ducts is recom-
mended.
Attach surge absorbers or noise filters to peripheral devices
that generate noise (e.g., motors, transformers, solenoids,
magnetic coils, or other equipment that has an inductance
element). If using a noise filter with the power supply, be sure
to confirm the voltage and the current, and then mount the
power supply as near as possible to the Temperature Con-
troller.
Set up the Temperature Controller, along with its power sup-
ply, as far away as possible from devices that generate
strong, high-frequency waves, such as high-frequency weld-
ers and high-frequency machines, and from devices that gen-
erate surges.
onds of turning the power ON.
warm up.
heater) at the same time as or before supplying power to the
Temperature Controller. If power is turned ON for the Tem-
perature Controller before turning ON power for the load,
self-tuning will not be performed properly and optimum con-
trol will not be achieved.
(c)Copyright OMRON Corporation 2007 All Rights Reserved.
sulfide gas and ammonia gas)
Operating Environment Precautions
2
2
) to AWG14 (2.081 mm
) for terminals 7 to 9. The exposed current-carry-
7.2 mm max.
2
) for terminals 1 to 6, and
2
) to AWG22
C-1