SNAP-IT-RM-D64 OPTO 22, SNAP-IT-RM-D64 Datasheet - Page 3

• Manufacturer Part Number: SNAP-IT-RM-D64
• Description: Controllers
• Manufacturer: OPTO 22

Specifications of SNAP-IT-RM-D64

• Peak Reflow Compatible (260 C): No
• Leaded Process Compatible: No
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

© 2004 Opto 22. All rights reserved. All trademarks, trade names, logos, and service marks referenced herein belong to their respective companies.
DATA SHEET
Form 1240-050801
Opto 22 • 43044 Business Park Drive • Temecula, CA 92590-3614 • Phone: [phone] • (800) 321-OPTO • Fax: [phone] • www.opto22.com
Available Models
and electronic devices. Digital devices are devices that can be in
one of only two states: either on or off. Dry contacts and door
sensors are examples of digital devices. SNAP-IT-RM-D64 can
monitor and manage up to 64 points from digital devices, each
point either an input that reports the device’s on/off status or an
output that turns it on and off remotely.
Specifications
Description (continued)
Protocols
Ethernet Port
Power Supply
Power Cord
Power Consumption
Dimensions
SNAP-IT-RM
Communications
Serial Port
Other Specifications
(order separately)
Humidity
Temperature
SNAP-IT-RM-D64 can monitor digital electrical, mechanical,
SNAP-IT-RM-ADS and SNAP-IT-RM-UADS can monitor
Inside Sales: (800) 321-OPTO • Product Support: (800) TEK-OPTO • [phone] • Fax: [phone] • Email: [e-mail]
19-inch rack-mount enclosure, 3U.
17.35" W, 5.22" H, 6.625" D (box only;
Modbus/TCP, SNMP, SMTP, FTP, and
IEEE 1394-based protocols over
10/100 Mbps Fast Ethernet, using
RS-232. Default rate is 19,200 Kbd;
baud rate is soft-selectable from 2400 to
115,200 Kbd.
UL rated 120–250 VAC
Manufacturer rated 100–250 VAC
(48 VDC and other options available by
120 VAC United States, 240 VAC United
Kingdom, or 240 VAC international
7.5" D with modules)
TCP/IP, UDP/IP, and PPP
Category 5 or better solid UTP cable
with RJ-45 connector
special order)
30 W
0° to 70° C operating
-30° to 85° C storage
0–95% humidity, non-condensing
analog, digital, and serial electrical, mechanical, and electronic
devices. Analog devices are devices that have a range of possible
values, such as temperature or pressure sensors. Digital devices
can be either on or off. Serial devices, such as chart recorders and
barcode readers, communicate by sending ASCII characters via a
serial port. SNAP-IT-RM-ADS and SNAP-IT-RM-UADS can also
use SNAP-PID-V modules; each PID module monitors input signals
and adjusts output signals to control one proportional-integral-
derivative (PID) loop.
SNAP-IT Status LEDs
100MB
10MB
ACT
ERD
RUN
SRD
LED
ETD
STD
3VF
5VF
FLT
FD
Network Activity
Full Duplex Mode
Ethernet—Receive Data
Ethernet—Transmit Data
Ethernet Link Detection at 10 Mbps
Ethernet Link Detection at 100 Mbps
Normal Operation
Microprocessor Fault
3 Volt Fault
5 Volt Fault
Serial—Receive Data
Serial—Transmit Data
RACK MOUNT
SNAP-IT
Indicates
page 3/5