TL-T2E15 Omron, TL-T2E15 Datasheet - Page 8
![Inductive Proximity Sensor](/photos/20/0/200091/4438345_sml.jpg)
TL-T2E15
Manufacturer Part Number
TL-T2E15
Description
Inductive Proximity Sensor
Manufacturer
Omron
Series
TL-Tr
Specifications of TL-T2E15
Sensor Input
Inductive
Sensing Range
2mm
Supply Voltage Range Dc
10V To 30V
Sensing Range Max
2mm
Sensor Housing
Rectangular
Switch Terminals
Cable
Sensor Output
NPN Voltage-Current Output
Sensing Distance
0.079" (2mm)
Sensor Type
Inductive
Sensing Object
Metallic
Response Frequency
800Hz
Material - Body
ABS Resin
Shielding
Shielded
Voltage - Supply
10 V ~ 30 V
Output Type
NPN-NO
Terminal Type
3-Wire
Package / Case
Box
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
●Design
Sensing Object Material
The sensing distance varies greatly depending on the material of the
sensing object. Study the engineering data for the influence of
sensing object material and size and select a distance with sufficient
leeway.
Size of Sensing Object
In general, if the object is smaller
than the standard sensing
object, the sensing distance
decreases.
• In general, if the
• Design the setup for an object
• When the size of the standard
sensing object is a non-
magnetic metal (for
example, aluminum),
the sensing distance
decreases.
size that is the same or greater
than the standard sensing
object size from the graphs
showing the sensing object
size and sensing distance.
sensing object is the same or
less than the size of the
standard sensing object,
select a sensing distance with
sufficient leeway.
http://www.ia.omron.com/
Example: E2-X10D@
14
12
10
8
6
4
2
0
5 10 15 20 25 30 35 40 45 50 55
Side length (one side) of sensing object: d (mm)
Sensing
distance
becomes
short
X
t=1mm
d
Standard
sensing
object
Aluminum
Side length (one side)
of sensing object: d (mm)
Stainless steel
Stability
(SPCC)
Copper
Brass
Steel
Proximity Sensors Technical Guide
Thickness of Sensing Object
Effect of Plating (Typical)
(Reference values: Percent of non-plated sensing distance)
Mutual Interference
Power Reset Time
A Sensor is ready for detection within 100 ms after turning ON the
power. If the load and Sensor are connected to separate power
supplies, design the system so that the Sensor power turns ON first.
• The thickness of ferrous metals
• For non-magnetic metal, a
• Influence of Plating If the sensing object is plated, the sensing
Thickness and base material of
plating
No plating
Zn 5 to 15 μm
Cd 5 to 15 μm
Ag 5 to 15 μm
Cu 10 to 20 μm
Cu 5 to 15 μm
Cu (5 to 10 μm) + Ni (10 to 20 μm)
Cu (5 to 10 μm) + Ni (10 μm)
+ Cr (0.3 μm)
• Mutual interference refers to a state where a Sensor is affected by
• One means of avoiding interference when mounting Proximity
• When Proximity Sensors with the same frequency are mounted
(iron, nickel, etc.) must be 1 mm
or greater.
sensing distance equivalent to a
magnetic body can be obtained
when the coating thickness is
0.01 mm or less. With pulse-
response models (e.g., E2V),
however, the characteristics may
vary. Be sure to check the
catalog information for the
relevant model.
When the coating is extremely
thin and is not conductive, such
as a vacuum deposited film,
detection is not possible.
distance will change (see the table below).
magnetism (or static capacitance) from an adjacent Sensor and the
output is unstable.
Sensors close together is to alternate Sensors with different
frequencies. The model tables indicate whether different
frequencies are available. Please refer to the tables.
together in a line or face-to-face, they must be separated by a
minimum distance. For details, refer to Mutual Interference in the
Safety Precautions for individual Sensors.
(c)Copyright OMRON Corporation 2008 All Rights Reserved.
10
8
6
4
2
100 to 110
90 to 120
0 0.01
60 to 90
70 to 95
70 to 95
75 to 95
Thickness of sensing object: t (mm)
Steel
100
Sensing object shape: Square
-
0.1
95 to 105
95 to 105
85 to 100
95 to 105
95 to 105
Brass
Aluminum
1
100
Steel
-
-
d=30mm
Reset
Operate
10
C-3