TL-T2E15 Omron, TL-T2E15 Datasheet
![Inductive Proximity Sensor](/photos/20/0/200091/4438345_sml.jpg)
TL-T2E15
Specifications of TL-T2E15
Related parts for TL-T2E15
TL-T2E15 Summary of contents
Page 1
... Ideal for side-by-side mounting. Be sure to read Safety Precautions on page 5. Ordering Information Appearance Sensing distance 2 mm Shielded 5 mm Unshielded Note: Models with a different frequency are available. The model numbers are TL-T@@@5. (e.g., TL-T2E15). http://www.ia.omron.com/ Output specifications NO TL-T2E1 NPN DC 3-wire models TL-T2F1 PNP ...
Page 2
... Material Heat-resistant ABS resin Sensing surface Accessories Instruction sheet http://www.ia.omron.com/ TL-T2Y1 TL-T5ME1 TL-T2Y2 TL-T5ME2 5 mm±10 Iron 15 × 15 × models: 250 Hz, Y models 100 to 220 VAC (90 to 250 VAC) 50/ 200 mA Refer to Residual Voltage (Typical) on page 3. Refer to I/O Circuit Diagrams Timing Chart on page 4. ...
Page 3
... Side length of sensing object: d (mm) TL-T@(M)Y@ at 200 VAC Residual output voltage 200 ON V 200 VAC A 50 Residual load voltage OFF 100 150 200 Load current (mA) (c)Copyright OMRON Corporation 2008 All Rights Reserved. TL-T TL-T5M 6 Iron 5 Stainless steel (SUS304 Brass 2 Aluminum @ ...
Page 4
... Models mode specifications TL-T2E1 NO TL-T5ME1 NPN TL-T2E2 NC TL-T5ME2 TL-T2F1 NO PNP AC 2-wire Models Operation mode Models TL-T2Y1 NO TL-T5MY1 TL-T2Y2 NC TL-T5MY2 http://www.ia.omron.com/ Timing charts Present Sensing object Not present Load Operate (between brown and black) Reset Output voltage H (between black L and blue) ...
Page 5
... Be sure to separate the Sensor from surrounding metal objects as shown in the following illustration • The TL-T2 will not be influenced by metal when it is embedded in metal. Dimensions TL-T@ In the interest of product improvement, specifications are subject to change without notice. http://www.ia.omron.com/ Mutual Interference When two or more Sensors are mounted face-to-face or side- by-side, separate them as shown below ...
Page 6
... Be sure that the power supply polarity and oth- er wiring is correct. Incorrect wiring may cause explosion or burning. Connection without a Load If the power supply is connected directly with- out a load, the internal elements may explode or burn. Be sure to insert a load when connect- ing the power supply. ...
Page 7
... Conduits, ducts, pre-wired, terminal wiring, ease of main- tenance and inspection mT* max. Do not use the Sensor at a level higher than 20 mT. Life: Power-ON time/frequency of use (c)Copyright OMRON Corporation 2008 All Rights Reserved. Peripheral metal Sensing distance Material, distance Fluctuation in transit point, al- to Sensor, orien- lowable error, etc ...
Page 8
... Sensing Object Material The sensing distance varies greatly depending on the material of the sensing object. Study the engineering data for the influence of sensing object material and size and select a distance with sufficient leeway. • In general, if the Example: E2-X10D@ sensing object is a non- ...
Page 9
... OFF It is recommend that leeway be included in the actual values used. For 12 VDC, use 15 kΩ or less and 450 mW or higher, and for 24 VDC, use 30 kΩ or less and 0 higher. (c)Copyright OMRON Corporation 2008 All Rights Reserved. AC power supply voltage Vs 2 (mW) ...
Page 10
... Loads with Large Inrush Current Loads, such as lamps or motors, that cause a large inrush weaken or damage the switching element. In this situation, use a relay. * E2K, TL-N@ higher ●Mounting Mounting the Sensor When mounting a Sensor, do not tap it with a hammer or otherwise subject it to excessive shock. This will weaken water resistance and may damage the Sensor ...
Page 11
... A parallel connection can be used if A and B will not be operated simulta- neously and there is no need to hold the load. The leakage current, however, Load will be n times the value for each Sensor and reset failures will frequently oc- cur. ("n" is the number of Proximity Sensors and B will be operated simultaneously and the load is held, a parallel con- nection is not possible ...
Page 12
... The residual voltage of the E2E-XD-M1J 3-Wire Sensors Operation can be reversed with the signal input switch on the S3D2. (c)Copyright OMRON Corporation 2008 All Rights Reserved. Description Example: A maximum of two Sensors can be used when an MY (24-VDC) Relay is used for the load ...
Page 13
... Disassembly and Repair Do not under any circumstances attempt to disassemble or repair the product. Quick Failure Check You can conveniently check for failures by connecting the E39-VA Handy Checker to check the operation of the Sensor. http://www.ia.omron.com/ Proximity Sensors Technical Guide (c)Copyright OMRON Corporation 2008 All Rights Reserved. ...
Page 14
... Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you have any questions or comments. WARRANTY OMRON's exclusive warranty is that the products are free from defects in materials and workmanship for a period of one year (or other period if specifi ed) from date of sale by OMRON. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, REGARDING NON-INFRINGEMENT, MERCHANTABILITY, OR FITNESS FOR PARTICULAR PURPOSE OF THE PRODUCTS ...