SMB55RA BANNER ENGINEERING, SMB55RA Datasheet - Page 4

• Manufacturer Part Number: SMB55RA
• Description: Sensor Mounting Bracket
• Manufacturer: BANNER ENGINEERING

Specifications of SMB55RA

• For Use With: R58E Series Expert Register Mark Sensors
• Lead Free Status / Rohs Status: RoHS Compliant part

In Static TEACH mode, the sensor learns two sensing conditions after each is presented one
time. The sensor automatically positions the switchpoint midway between the two conditions.
See Figure 3.
NOTE: T he sensor will return to RUN mode if either TEACH condition is not registered within
Static TEACH and Manual Adjust
Sensitivity may be adjusted at any time when the sensor is in RUN mode by clicking the “+”
and “-” buttons. Each click translates to 1/2 segment on the signal strength bargraph display.
For best sensing reliability, both sensing conditions should register equally distant from the
switchpoint on the signal strength bargraph display.
4
R58 Expert
P/N 122928 rev. C
T
T
T
60 seconds. TEACH mode may be cancelled by pressing and holding the Static push
button for ≥ 2 seconds. In either case, the sensor will revert to the previous conditions
taught (i.e., exit without save).
> 2 seconds
• P ush and hold the Static
• P resent the 1st sensing
• “ Click” the Static push
• P resent the 2nd sensing
• “ Click” the Static push
push button for
> 2 seconds.
condition.
button.
condition.
button.
0.04 sec. ≤ “click” ≤ 0.8 sec.
Push Button
T
™
T T T
T
T
T
T
T
T
Registration Mark Sensors
T
T
T
T
T
T
Procedure
T
T
T
T
T
T
Static TEACH
T
T
T
• N o action required; sensor
• P resent the 1st sensing
• Single-pulse the remote line.
• Wait at least 0.8 seconds.
• P resent the 2nd sensing
• S ingle-pulse the remote line.
is ready for the 1st sensing
condition.
condition.
condition.
T
T
T
T
T
T
0.04 sec. ≤ “T” ≤ 0.8 sec.
T
T
T
T
Remote Line
T
T
T
T
T
T
T
T
T
T
T
T
0.8 seconds
> 2 seconds
T
T
T
T
T
T
T
T
T
T
T
T
T
T T T
T
T
T
LO and DO: Alternately flash Green
Output: ON Yellow (indicating ready to teach 1st sensing condition)
Bargraph display: Goes OFF
LO and DO: Alternately flash Green
Output: OFF (indicating ready to teach 2nd sensing condition)
Bargraph display: Remains OFF
• B argraph display flashes one segment for three seconds to indicate
• S ensor enters RUN mode.
• P airs of bargraph display segments flash for three seconds to indicate low
• Sensor returns to TEACH 1st sensing condition.
T
T
T
relative contrast (see contrast table on page 5).
contrast.
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
Banner Engineering Corp. • Minneapolis, MN U.S.A
T
T
T
T
www.bannerengineering.com • Tel: [phone]
T
T
T
T
T
T
Teach Unacceptable
Figure 2. Static TEACH (Light Operate shown)
T
T
T
(push button only)
0.8 seconds
Teach Accepted
T
T
T
Longer Duration
Condition of
T
T
T
2nd Taught
Condition
Result
Output OFF
Output OFF
T
T
T
T
T
T
between taught conditions
between taught conditions
threshold midway
threshold midway
Sensor positions
Sensor positions
Manual Adjust
Manual Adjust
adjusted by
adjusted by
Position
Position
Output ON
Output ON
Shorter Duration
Condition of
1st Taught
Condition