AS5163-HTST-500 austriamicrosystems, AS5163-HTST-500 Datasheet - Page 29

• Manufacturer Part Number: AS5163-HTST-500
• Description: IC ENCODER ROTARY 14-TSSOP
• Manufacturer: austriamicrosystems
• Type: Linear, Rotary Encoder - Programmabler

Specifications of AS5163-HTST-500

• Featured Product: AS5163 - Contactless Magnetic Angle Position Sensor
• Sensing Range: 30mT ~ 70mT
• Voltage - Supply: 4.5 V ~ 5.5 V
• Current - Supply: 20mA
• Output Type: Analog, Ratiometric
• Operating Temperature: -40°C ~ 150°C
• Package / Case: 14-TSSOP (0.173", 4.40mm Width)
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Current - Output (max): -
• Features: -
• Other names: AS5163-HTST-500TR

AS5163
Datasheet - A p p l i c a t i o n I n f o r m a t i o n
Data Content.
www.austriamicrosystems.com/AS5163
Redundancy Code
Redundancy <7:0>
Redundancy (7:0): For a better programming reliability, a redundancy is implemented. In case the programming of one bit fails, then this
function can be used. With an address (7:0) one bit can be selected and programmed.
Lock_OTPCUST = 1, locks the customer area in the OTP and the device is starting up from now on in operating mode.
Invert_Slope = 1, inverts the output characteristic in analog output mode.
Gain (7:0): With this value one can adjust the steepness of the output slope.
EXT_RANGE = 1, provides a wider z-Range of the magnet by turning off the alarm function.
FAST_SLOW = 1, improves the noise performance due to internal filtering.
BP (13:0): The breakpoint can be set with resolution of 14 bit.
PWM Frequency (1:0): Four different frequency settings are possible. Please refer to
KDHYS (1:0): Avoids flickering at the KDOWN output (pin 11). For settings, refer to
OffsetOut (11:0): Output characteristic parameter
ANALOG_PWM = 1, selects the PWM output mode.
OffsetIn (13:0): Output characteristic parameter
DIAG_HIGH = 1: In case of an error, the signal goes into high failure-band.
ClampHI (6:0): Sets the clamping level high with respect to VDD.
DAC_MODE disables filter at DAC
ClampLow (6:0): Sets the clamping level low with respect to VDD.
KD (5:0): Sets the kick-down level with respect to VDD.
in decimal
11 - 17
19 - 32
33 - 46
47 - 60
61 - 72
78 - 83
84 - 85
4 - 10
18
73
74
75
76
77
86
0
1
2
3
ClampLow<6> - ClampLow<0>
OffsetOut<11> - OffsetOut<0>
ClampHi<6> - ClampHi<0>
OffsetIn<13> - OffsetIn<0>
KDHYS<1> - KDHYS<0>
PWM Frequency<0>
PWM Frequency<1>
Gain<13> - Gain<0>
OTP Bit Selection
BP<13> - BP<0>
Lock_OTPCUST
KD<5> - KD<0>
OP_Mode<1>
OP_Mode<0>
FAST_SLOW
EXT_RANGE
DAC_MODE
DIAG_HIGH
Invert_Slope
none
Revision 2.7
Table
Table
13.
11.
29 - 36