PIC16F916T-I/SS Microchip Technology, PIC16F916T-I/SS Datasheet - Page 91

• Manufacturer Part Number: PIC16F916T-I/SS
• Description: IC,MICROCONTROLLER,8-BIT,PIC CPU,CMOS,SSOP,28PIN,PLASTIC
• Manufacturer: Microchip Technology
• Series: PIC® 16Fr

Specifications of PIC16F916T-I/SS

• Rohs Compliant: YES
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LCD, POR, PWM, WDT
• Number Of I /o: 24
• Program Memory Size: 14KB (8K x 14)
• Program Memory Type: FLASH
• Eeprom Size: 256 x 8
• Ram Size: 352 x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 5.5 V
• Data Converters: A/D 5x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-SSOP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: MA160011 - DAUGHTER BOARD PICDEM LCD 16F91X
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

4.3
Clock Source modes can be classified as external or
internal.
• External Clock modes rely on external circuitry for
• Internal clock sources are contained internally
The system clock can be selected between external or
internal clock sources via the System Clock Select
(SCS) bit of the OSCCON register. See Section 4.6
“Clock Switching” for additional information.
TABLE 4-1:
4.4.2
The External Clock (EC) mode allows an externally
generated logic level as the system clock source. When
operating in this mode, an external clock source is
connected to the OSC1 input and the OSC2 is available
for general purpose I/O. Figure 4-2 shows the pin
connections for EC mode.
The Oscillator Start-up Timer (OST) is disabled when
EC mode is selected. Therefore, there is no delay in
operation after a Power-on Reset (POR) or wake-up
from Sleep. Because the PIC
static, stopping the external clock input will have the
effect of halting the device while leaving all data intact.
Upon restarting the external clock, the device will
resume operation as if no time had elapsed.
© 2007 Microchip Technology Inc.
the clock source. Examples are: Oscillator mod-
ules (EC mode), quartz crystal resonators or
ceramic resonators (LP, XT and HS modes) and
Resistor-Capacitor (RC) mode circuits.
within the Oscillator module. The Oscillator
module has two internal oscillators: the 8 MHz
High-Frequency Internal Oscillator (HFINTOSC)
and the 31 kHz Low-Frequency Internal Oscillator
(LFINTOSC).
LFINTOSC (31 kHz)
LFINTOSC (31 kHz)
Switch From
Sleep/POR
Sleep/POR
Sleep/POR
Clock Source Modes
EC MODE
OSCILLATOR DELAY EXAMPLES
®
MCU design is fully
HFINTOSC
HFINTOSC
LFINTOSC
LP, XT, HS
Switch To
EC, RC
EC, RC
PIC16F913/914/916/917/946
125 kHz to 8 MHz
32 kHz to 20 MHz
125 kHz to 8 MHz
DC – 20 MHz
DC – 20 MHz
Frequency
31 kHz
4.4
4.4.1
If the Oscillator module is configured for LP, XT or HS
modes, the Oscillator Start-up Timer (OST) counts
1024 oscillations from OSC1. This occurs following a
Power-on Reset (POR) and when the Power-up Timer
(PWRT) has expired (if configured), or a wake-up from
Sleep. During this time, the program counter does not
increment and program execution is suspended. The
OST ensures that the oscillator circuit, using a quartz
crystal resonator or ceramic resonator, has started and
is providing a stable system clock to the Oscillator
module. When switching between clock sources, a
delay is required to allow the new clock to stabilize.
These oscillator delays are shown in Table 4-1.
In order to minimize latency between external oscillator
start-up and code execution, the Two-Speed Clock
Start-up mode can be selected (see Section 4.7
“Two-Speed Clock Start-up Mode”).
FIGURE 4-2:
Note 1:
Clock from
Ext. System
External Clock Modes
OSCILLATOR START-UP TIMER (OST)
Alternate pin functions are listed in
Section 1.0 “Device Overview”.
2 instruction cycles
1024 Clock Cycles (OST)
Oscillator Warm-Up Delay (T
1 cycle of each
1 μs (approx.)
I/O
EXTERNAL CLOCK (EC)
MODE OPERATION
Oscillator Delay
OSC1/CLKIN
OSC2/CLKOUT
PIC
DS41250F-page 89
®
MCU
(1)
WARM
)