DSPIC30F3010-20E/SO Microchip Technology, DSPIC30F3010-20E/SO Datasheet - Page 51
![no-image](/images/manufacturer_photos/0/4/439/microchip_technology_sml.jpg)
DSPIC30F3010-20E/SO
Manufacturer Part Number
DSPIC30F3010-20E/SO
Description
IC,DSP,16-BIT,CMOS,SOP,28PIN,PLASTIC
Manufacturer
Microchip Technology
Series
dsPIC™ 30Fr
Datasheets
1.DSPIC30F2011-20ISO.pdf
(66 pages)
2.DSPIC30F2011-20IP.pdf
(26 pages)
3.DSPIC30F3010-30ISO.pdf
(228 pages)
4.DSPIC30F3010-30ISO.pdf
(18 pages)
5.DSPIC30F3010-30ISO.pdf
(6 pages)
6.DSPIC30F3010-30ISO.pdf
(16 pages)
7.DSPIC30F3010-30ISO.pdf
(22 pages)
Specifications of DSPIC30F3010-20E/SO
Rohs Compliant
YES
Core Processor
dsPIC
Core Size
16-Bit
Speed
20 MIPS
Connectivity
I²C, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, Motor Control PWM, QEI, POR, PWM, WDT
Number Of I /o
20
Program Memory Size
24KB (8K x 24)
Program Memory Type
FLASH
Eeprom Size
1K x 8
Ram Size
1K x 8
Voltage - Supply (vcc/vdd)
2.5 V ~ 5.5 V
Data Converters
A/D 6x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 125°C
Package / Case
28-SOIC (7.5mm Width)
Package
28SOIC W
Device Core
dsPIC
Family Name
dsPIC30
Maximum Speed
20 MHz
Operating Supply Voltage
3.3|5 V
Data Bus Width
16 Bit
Interface Type
I2C/SPI/UART
On-chip Adc
6-chx10-bit
Number Of Timers
5
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
DSPIC30F3010-20E/SO
Manufacturer:
MICROCHIP
Quantity:
1 340
Company:
Part Number:
DSPIC30F3010-20E/SO
Manufacturer:
MICROCHIP
Quantity:
1 000
6.0
The dsPIC30F family of devices contains internal
program Flash memory for executing user code. There
are two methods by which the user can program this
memory:
1.
2.
6.1
dsPIC30F devices can be serially programmed while in
the end application circuit. This is simply done with two
lines for Programming Clock and Programming Data
(which are named PGC and PGD, respectively), and
three other lines for Power (V
Master Clear (MCLR). This allows customers to manu-
facture boards with unprogrammed devices, and then
program the microcontroller just before shipping the
product. This also allows the most recent firmware or a
custom firmware to be programmed.
FIGURE 6-1:
© 2010 Microchip Technology Inc.
Note:
In-Circuit
capabilities
Run-Time Self-Programming (RTSP)
FLASH PROGRAM MEMORY
In-Circuit Serial Programming
(ICSP)
This data sheet summarizes features of
this group of dsPIC30F devices and is not
intended to be a complete reference
source. For more information on the CPU,
peripherals, register descriptions and
general device functionality, refer to the
“dsPIC30F Family Reference Manual”
(DS70046). For more information on the
device instruction set and programming,
refer to the “16-bit MCU and DSC
Programmer’s
(DS70157).
Serial
User/Configuration
Space Select
ADDRESSING FOR TABLE AND NVM REGISTERS
Programming™
Reference
DD
Using
NVMADR
Addressing
Using
Table
Instruction
), Ground (V
Using
Program
Counter
(ICSP™)
1/0
1/0
Manual”
0
SS
) and
TBLPAG Reg
NVMADRU Reg
8 bits
8 bits
Program Counter
6.2
RTSP is accomplished using TBLRD (table read) and
TBLWT (table write) instructions.
With RTSP, the user may erase program memory,
32 instructions (96 bytes) at a time and can write
program memory data, 32 instructions (96 bytes) at a
time.
6.3
The TBLRDL and the TBLWTL instructions are used to
read or write to bits<15:0> of program memory.
TBLRDL and TBLWTL can access program memory in
Word or Byte mode.
The TBLRDH and TBLWTH instructions are used to read
or write to bits<23:16> of program memory. TBLRDH
and TBLWTH can access program memory in Word or
Byte mode.
A 24-bit program memory address is formed using
bits<7:0> of the TBLPAG register and the Effective
Address (EA) from a W register specified in the table
instruction, as shown in
24 bits
24-bit EA
dsPIC30F3010/3011
NVMADR Reg EA
Working Reg EA
Run-Time Self-Programming
(RTSP)
Table Instruction Operation Summary
16 bits
16 bits
Figure
0
Byte
Select
6-1.
DS70141F-page 51