LPC2366FBD100 NXP Semiconductors, LPC2366FBD100 Datasheet - Page 20

no-image

LPC2366FBD100

Manufacturer Part Number
LPC2366FBD100
Description
IC, 32BIT MCU, ARM7, 72MHZ, LQFP-100
Manufacturer
NXP Semiconductors
Datasheet

Specifications of LPC2366FBD100

Controller Family/series
(ARM7)
No. Of I/o's
70
Ram Memory Size
58KB
Cpu Speed
72MHz
No. Of Timers
4
No. Of Pwm Channels
6
Core Size
32 Bit
Program Memory Size
256KB
Embedded Interface Type
CAN, SPI, USB, UART
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
LPC2366FBD100
Manufacturer:
NXP
Quantity:
1 337
Part Number:
LPC2366FBD100
Manufacturer:
NXP
Quantity:
86 755
Part Number:
LPC2366FBD100
Manufacturer:
ST
0
Part Number:
LPC2366FBD100
Manufacturer:
NXP/恩智浦
Quantity:
20 000
Part Number:
LPC2366FBD100
0
Part Number:
LPC2366FBD100,551
Quantity:
9 999
Part Number:
LPC2366FBD100,551
Manufacturer:
NXP Semiconductors
Quantity:
10 000
NXP Semiconductors
LPC2364_65_66_67_68_6
Product data sheet
7.8 Fast general purpose parallel I/O
Device pins that are not connected to a specific peripheral function are controlled by the
GPIO registers. Pins may be dynamically configured as inputs or outputs. Separate
registers allow setting or clearing any number of outputs simultaneously. The value of the
output register may be read back as well as the current state of the port pins.
LPC2364/65/66/67/68 use accelerated GPIO functions:
Single DMA and burst DMA request signals. Each peripheral connected to the
GPDMA can assert either a burst DMA request or a single DMA request. The DMA
burst size is set by programming the GPDMA.
Memory-to-memory, memory-to-peripheral, peripheral-to-memory, and
peripheral-to-peripheral transfers.
Scatter or gather DMA is supported through the use of linked lists. This means that
the source and destination areas do not have to occupy contiguous areas of memory.
Hardware DMA channel priority. Each DMA channel has a specific hardware priority.
DMA channel 0 has the highest priority and channel 1 has the lowest priority. If
requests from two channels become active at the same time the channel with the
highest priority is serviced first.
AHB slave DMA programming interface. The GPDMA is programmed by writing to the
DMA control registers over the AHB slave interface.
One AHB master for transferring data. This interface transfers data when a DMA
request goes active.
32-bit AHB master bus width.
Incrementing or non-incrementing addressing for source and destination.
Programmable DMA burst size. The DMA burst size can be programmed to more
efficiently transfer data. Usually the burst size is set to half the size of the FIFO in the
peripheral.
Internal four-word FIFO per channel.
Supports 8-bit, 16-bit, and 32-bit wide transactions.
An interrupt to the processor can be generated on a DMA completion or when a DMA
error has occurred.
Interrupt masking. The DMA error and DMA terminal count interrupt requests can be
masked.
Raw interrupt status. The DMA error and DMA count raw interrupt status can be read
prior to masking.
GPIO registers are relocated to the ARM local bus so that the fastest possible I/O
timing can be achieved.
Mask registers allow treating sets of port bits as a group, leaving other bits
unchanged.
All GPIO registers are byte and half-word addressable.
Entire port value can be written in one instruction.
Rev. 06 — 1 February 2010
LPC2364/65/66/67/68
Single-chip 16-bit/32-bit microcontrollers
© NXP B.V. 2010. All rights reserved.
20 of 59

Related parts for LPC2366FBD100