PCA9624PW NXP Semiconductors, PCA9624PW Datasheet - Page 6
![no-image](/images/manufacturer_photos/0/4/487/nxp_semiconductors_sml.jpg)
PCA9624PW
Manufacturer Part Number
PCA9624PW
Description
IC, LED DRIVER, RGBA, 24-TSSOP
Manufacturer
NXP Semiconductors
Datasheet
1.PCA9624BS118.pdf
(37 pages)
Specifications of PCA9624PW
No. Of Outputs
8
Output Current
100mA
Output Voltage
40V
Input Voltage
2.3V To 5.5V
Dimming Control Type
PWM
Driver Case Style
TSSOP
Switching Frequency
1MHz
Base Number
9624
Operating
RoHS Compliant
Led Driver Application
RGB Or RGBA LED Drivers, LED Status Information, Displays, Backlights
Rohs Compliant
Yes
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PCA9624PW
Manufacturer:
PHILIPS
Quantity:
5 542
Part Number:
PCA9624PW
Manufacturer:
NXP/恩智浦
Quantity:
20 000
Part Number:
PCA9624PW,112
Manufacturer:
NXP/恩智浦
Quantity:
20 000
Part Number:
PCA9624PW,118
Manufacturer:
NXP/恩智浦
Quantity:
20 000
Company:
Part Number:
PCA9624PW118
Manufacturer:
NXP Semiconductors
Quantity:
135
Company:
Part Number:
PCA9624PWЈ¬112
Manufacturer:
NXP
Quantity:
551
NXP Semiconductors
7. Functional description
PCA9624_2
Product data sheet
7.1.1 Regular I
7.1 Device addresses
[1]
Refer to
Following a START condition, the bus master must output the address of the slave it is
accessing.
There are a maximum of 128 possible programmable addresses using the 7 hardware
address pins. Two of these addresses, Software Reset and LED All Call, cannot be used
because their default power-up state is ON, leaving a maximum of 126 addresses. Using
other reserved addresses, as well as any other Sub Call address, will reduce the total
number of possible addresses even further.
The I
internal pull-up resistors are incorporated on the hardware selectable address pins and
they must be pulled HIGH or LOW.
Remark: Using reserved I
devices are on the bus and/or the bus will be open to other I
date. In a closed system where the designer controls the address assignment these
addresses can be used since the PCA9624 treats them like any other address. The
LED All Call, Software Rest and PCA9564 or PCA9665 slave address (if on the bus) can
never be used for individual device addresses.
Fig 4.
•
•
•
•
•
•
HVQFN24 package supply ground is connected to both V
be connected to supply ground for proper device operation. For enhanced thermal, electrical, and board
level performance, the exposed pad needs to be soldered to the board using a corresponding thermal pad
on the board and for proper heat conduction through the board, thermal vias need to be incorporated in the
PCB in the thermal pad region.
PCA9624 LED All Call address (1110 000) and Software Reset (0000 0110) which
are active on start-up
PCA9564 (0000 000) or PCA9665 (1110 000) slave address which is active on
start-up
‘reserved for future use’ I
slave devices that use the 10-bit addressing scheme (1111 0XX)
slave devices that are designed to respond to the General Call address (0000 000)
High-speed mode (Hs-mode) master code (0000 1XX)
2
C-bus slave address of the PCA9624 is shown in
Figure 1 “Block diagram of
Slave address
2
C-bus slave address
Rev. 02 — 26 August 2009
2
C-bus addresses will interfere with other devices, but only if the
2
C-bus addresses (0000 011, 1111 1XX)
A6
A5
hardware selectable
PCA9624”.
slave address
A4
A3
8-bit Fm+ I
A2
A1
SS
pins and exposed center pad. V
002aab319
A0
Figure
2
R/W
C-bus 100 mA 40 V LED driver
2
C-bus systems at some later
4. To conserve power, no
PCA9624
© NXP B.V. 2009. All rights reserved.
SS
pins must
6 of 37