DS90LV001TLD National Semiconductor, DS90LV001TLD Datasheet - Page 7
![IC, LVDS BUFFER, LLP-8](/photos/19/1/190169/4579022_sml.jpg)
DS90LV001TLD
Manufacturer Part Number
DS90LV001TLD
Description
IC, LVDS BUFFER, LLP-8
Manufacturer
National Semiconductor
Datasheet
1.DS90LV001TLD.pdf
(16 pages)
Specifications of DS90LV001TLD
Supply Current
70mA
Supply Voltage Range
3V To 3.6V
Driver Case Style
LLP
No. Of Pins
8
Operating Temperature Range
-40°C To +85°C
Termination Type
SMD
Logic Type
Buffer
Transceiver Type
Buffer
Filter Terminals
SMD
Rohs Compliant
No
Data Rate
800Mbps
Data Rate Max
800Mbps
Family Type
LV
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
DS90LV001TLD/NOPB
Manufacturer:
NS
Quantity:
8 746
Company:
Part Number:
DS90LV001TLDX/NOPB
Manufacturer:
NS
Quantity:
8 597
Cable Repeater Application
Application Information
MODE OF OPERATION
The DS90LV001 can be used as a "stub-hider." In many sys-
tems, signals are distributed across backplanes, and one of
the limiting factors for system speed is the "stub length" or the
distance between the transmission line and the unterminated
receivers on the individual cards. Although it is generally rec-
ognized that this distance should be as short as possible to
maximize system performance, real-world packaging con-
cerns and PCB designs often make it difficult to make the
stubs as short as the designer would like. The DS90LV001,
available in the LLP (Leadless Leadframe Package) package,
can improve system performance by allowing the receiver to
be placed very close to the main transmission line either on
the backplane itself or very close to the connector on the card.
Longer traces to the LVDS receiver may be placed after the
DS90LV001. This very small LLP package is a 75% space
savings over the SOIC package.
INPUT FAILSAFE
The receiver inputs of the DS90LV001 do not have internal
failsafe biasing. For point-to-point and multidrop applications
with a single source, failsafe biasing may not be required.
When the driver is off, the link is in-active. If failsafe biasing
is required, this can be accomplished with external high value
resistors. Using the equations in the LVDS Owner"s Manual
Chapter 4, the IN+ should be pull to V
the IN− should be pull to GND with 12kΩ. This provides a
slight positive differential bias, and sets a known HIGH state
on the link with a minimum amount of distortion.
CC
(3.3V) with 20kΩ and
10133815
7
PCB LAYOUT AND POWER SYSTEM BYPASS
Circuit board layout and stack-up for the DS90LV001 should
be designed to provide noise-free power to the device. Good
layout practice also will separate high frequency or high level
inputs and outputs to minimize unwanted stray noise pickup,
feedback and interference. Power system performance may
be greatly improved by using thin dielectrics (4 to 10 mils) for
power/ground sandwiches. This increases the intrinsic ca-
pacitance of the PCB power system which improves power
supply filtering, especially at high frequencies, and makes the
value and placement of external bypass capacitors less criti-
cal. External bypass capacitors should include both RF ce-
ramic and tantalum electrolytic types. RF capacitors may use
values in the range 0.01 µF to 0.1 µF. Tantalum capacitors
may be in the range 2.2 µF to 10 µF. Voltage rating for tan-
talum capacitors should be at least 5X the power supply
voltage being used. It is recommended practice to use two
vias at each power pin of the DS90LV001 as well as all RF
bypass capacitor terminals. Dual vias reduce the interconnect
inductance by up to half, thereby reducing interconnect in-
ductance and extending the effective frequency range of the
bypass components.
The outer layers of the PCB may be flooded with additional
ground plane. These planes will improve shielding and isola-
tion as well as increase the intrinsic capacitance of the power
supply plane system. Naturally, to be effective, these planes
must be tied to the ground supply plane at frequent intervals
with vias. Frequent via placement also improves signal in-
tegrity on signal transmission lines by providing short paths
for image currents which reduces signal distortion. The
planes should be pulled back from all transmission lines and
component mounting pads a distance equal to the width of
the widest transmission line or the thickness of the dielectric
separating the transmission line from the internal power or
ground plane(s) whichever is greater. Doing so minimizes ef-
fects on transmission line impedances and reduces unwanted
parasitic capacitances at component mounting pads.
There are more common practices which should be followed
when designing PCBs for LVDS signaling. Please see appli-
cation note AN-1108 for guidelines. In addition, application
note AN-1187 has additional information specifically related
to LLP recommendations.
10133810
www.national.com