GCM188R71H103KA37D Murata, GCM188R71H103KA37D Datasheet - Page 23

• Manufacturer Part Number: GCM188R71H103KA37D
• Description: Multilayer Ceramic Capacitors (MLCC) - SMD/SMT 0603 0.01uF 50volts X7R 10%
• Manufacturer: Murata
• Series: GCMr

Specifications of GCM188R71H103KA37D

• Voltage Rating: 50 Volts
• Operating Temperature Range: - 55 C to + 125 C
• Temperature Coefficient / Code: X7R
• Product: Automotive MLCCs
• Dimensions: 0.8 mm W x 1.6 mm L x 0.8 mm H
• Termination Style: SMD/SMT
• Capacitance: 0.01 uF
• Tolerance: 10 %
• Package / Case: 0603 (1608 metric)
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

!Note
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
sales representatives or product engineers before ordering.
!Note
Chip monolithic ceramic capacitors (chips) can
experience degradation of termination solderability
when subjected to high temperature or humidity, or if
exposed to sulfur or chlorine gases.
Storage environment must be at an ambient temperature
of 5-40 degree C and an ambient humidity of 20-70%RH.
Use chip within 6 months. If 6 months or more have
elapsed, check solderability before use.
Insulation Resistance should be deteriorated on specific
condition of high humidity or incorrosion gas such as
hydrogen sulfide, sulfurous acid gas, chlorine. Those
condition are not suitable for use.
1. Inspection
2. Board Separation (or depanalization)
(1) Board flexing at the time of separation causes
(2) Severity of stresses imposed on the chip at the
(3) Board separation must be performed using special
!Caution (Storage and Operating Condition)
!Caution (Handling)
Thrusting force of the test probe can flex the PCB,
resulting in cracked chips or open solder joints.
Provide support pins on the back side of the PCB to
prevent warping or flexing.
cracked chips or broken solder.
time of board break is in the order of:
Pushback<Slitter<V Slot<Perforator.
jigs, not with hands.
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Use of Sn-Zn based solder will deteriorate
reliability of MLCC.
Please contact murata factory for the use of Sn-Zn
based solder in advance.
Do not use under the condition that causes
condensation. Use dampproof countermeasure if using
under the condition that causes condensation.
FAILURE TO FOLLOW THE ABOVE CAUTIONS MAY
RESULT, WORST CASE, IN A SHORT CIRCUIT
AND CAUSE FUMING OR PARTIAL DISPERSION
WHEN THE PRODUCT IS USED.
3. Reel and bulk case
FAILURE TO FOLLOW THE ABOVE CAUTIONS MAY
RESULT, WORST CASE, IN A SHORT CIRCUIT
AND FUMING WHEN THE PRODUCTS IS USED.
In the handling of reel and case, please be careful
and do not drop it.
Do not use chips from a case which has been dropped.
!Caution
C03E.pdf
21
09.3.31
1