SD356EVK/NOPB National Semiconductor, SD356EVK/NOPB Datasheet
SD356EVK/NOPB
Specifications of SD356EVK/NOPB
Related parts for SD356EVK/NOPB
SD356EVK/NOPB Summary of contents
Page 1
... These connectors will NOT mate to 2.4 mm connectors. Do not attempt to connect 2.4 mm connectors to the SD356EVK PC board. This will damage both the board and the connected device or cable. SD356EVK User Manual Rev 1.0 National Semiconductor EVK User Manual © 2008, National Semiconductor Corp. ...
Page 2
... SD356EVK. Do not allow heavy cables to hang unsupported from the connectors as they may break off the board. SD356EVK User Manual Rev 1.0 Control/Indicator LEDs Figure 1. SD356EVK board © 2008, National Semiconductor Corp. DC Power Connectors External Control Header SMBus Connector (not active) ...
Page 3
... The control lines of the LMH0356 SDI reclocker can be controlled by various means using the SD356EVK. The primary method for controlling these lines is the DIP switches located on the SD356EVK board. The DIP switches are labeled according to their function. When the switch actuator is pushed to the right SD356EVK User Manual Rev 1 © 2008, National Semiconductor Corp. ...
Page 4
... LED indicators are provided near the top of the board to indicate the state of the control inputs and the indicator outputs of the LMH0356 SDI reclocker. The LED states and their meanings are summarized in Table 1. SD356EVK User Manual Rev 1 © 2008, National Semiconductor Corp. ...
Page 5
... Gb/s signal or no signal detected LOCK DET Indicator on (green) when the LMH0356 reclocker is locked to the incoming signal © 2008, National Semiconductor Corp. Switch “Off” Function and Indication Select line pulled to logic 0 Indicator light turns green Rate line pulled to logic 0 Indicator light ...
Page 6
... SyntheSys Research BERTScope as a signal generator, eye diagram measurement device, and bit error rate test receiver. Other equivalent instruments could be used for thse measurements. The equipment used for testing the SD356EVK is listed in Table 2. SD356EVK User Manual Rev 1 © 2008, National Semiconductor Corp. ...
Page 7
... BERTScope Clock Out Data Out Data In Data+ Data- Data+ Data- UTIFlex Cable SD356 EVK Board SDI0 SDO SDI0 SDO SCO SCO VCC_IC VCC GND SMBus SMBus Controller Cable ` © 2008, National Semiconductor Corp. UTIFlex Cable UTIFlex Cable RF In HP8593E Spectrum Analyzer ...
Page 8
... SD356EVK User Manual Rev 1.0 Suggested Equipment Manufacturer Equipment Name SyntheSys BERTScope Research J-Bert Agilent Technologies Hewlett-Packard DC Power Supply Hewlett-Packard Portable Spectrum Analyzer Micro-Coax Inc. UTIFlex © 2008, National Semiconductor Corp. Model Number 12500B N4903A E3610A 8593E UFB205A- 0-0360- 000000 ...
Page 9
... Rev 1.0 Value 1.4835 Gb/s PRBS-7 200 © 2008, National Semiconductor Corp. Comments Any valid SMPTE data rate supported by the LMH0356 SDI reclocker can be used. These rates are 270 Mb/s, 1.485 Gb/s, 1.4835 Gb/s, 2.967 Gb/s, and 2.97 Gb/s This is a standard pseudorandom pattern 127 bits long ...
Page 10
... LOCK DET Indicator on (green), indicating that the LMH0356 reclocker is locked to the incoming signal © 2008, National Semiconductor Corp. Comments This is the setting for selecting input SDI0. Other selection settings can be used with other SDI inputs. This is the setting for automatic rate detect. ...
Page 11
... SDI reclocker. In concept simple input/output board with the LMH0356 SDI reclocker in the signal path. This manual has described the features of the PC board and its operation. Please also see the SDI Feature site at:: www.national.com/sdi SD356EVK User Manual Rev 1 © 2008, National Semiconductor Corp. ...