TDA3629/Y,112 NXP Semiconductors, TDA3629/Y,112 Datasheet
![no-image](/images/manufacturer_photos/0/4/487/nxp_semiconductors_sml.jpg)
TDA3629/Y,112
Specifications of TDA3629/Y,112
Related parts for TDA3629/Y,112
TDA3629/Y,112 Summary of contents
Page 1
DATA SHEET TDA3629 Light position controller Product specification File under Integrated Circuits, IC18 INTEGRATED CIRCUITS 1996 Sep 04 ...
Page 2
Philips Semiconductors Light position controller FEATURES Low positional error Low noise sensitivity due to hysteresis Low supply current Thermally protected Broken wire and short-circuit indication on SET input Brake function by short-circuiting the motor Hysteresis level set externally. QUICK REFERENCE ...
Page 3
Philips Semiconductors Light position controller BLOCK DIAGRAM handbook, full pagewidth 8(16) SET 1(1) FB Pin numbers in parenthesis represent the TDA3629T. 1996 Sep 04 PROTECTION - OVER VOLTAGE - UNDER VOLTAGE - TEMPERATURE TDA3629 SHORT-CIRCUIT I SET BROKEN WIRE INPUT ...
Page 4
Philips Semiconductors Light position controller PINNING SYMBOL TDA3629 OUT1 3 (1) n.c. 4 GND 5 OUT2 SET 8 Note 1. The pins which are not electrically connected should be connected to ...
Page 5
Philips Semiconductors Light position controller FUNCTIONAL DESCRIPTION The device is intended to control the elevation of the light beam of a head light of a passenger car. The driver can control the elevation of the light beam by rotating a ...
Page 6
Philips Semiconductors Light position controller The timing can be divided into several parts starting from a steady state (see Fig.5, the starting point, and Fig.10 for the application diagram): in this state (until T reference current is active, indicated by ...
Page 7
Philips Semiconductors Light position controller LIMITING VALUES In accordance with the Absolute Maximum Rating System (IEC 134). All voltages are defined with respect to ground. Positive currents flow into the device. Values measured in Fig.10. SYMBOL PARAMETER V supply voltage ...
Page 8
Philips Semiconductors Light position controller CHARACTERISTICS All voltages are defined with respect to ground. Positive currents flow into the device Values measured in Fig.10 with R SET SYMBOL PARAMETER Supply ...
Page 9
Philips Semiconductors Light position controller Notes to the characteristics 1. Steady state implies that the motor is not running (I 2. This is only valid when the temperature protection is not active the difference in voltage on ...
Page 10
Philips Semiconductors Light position controller TEST AND APPLICATION INFORMATION Automotive transients handbook, halfpage Fig.7 Worst case transients on V Worst case transients that may occur on the battery line V forms and the corresponding values are as illustrated in Figs ...
Page 11
Philips Semiconductors Light position controller Application diagrams and additional information Two possible application diagrams are shown. The first (see Fig.9) shows the best case: the lowest component count. The second (see Fig.10) shows additional components which may be necessary. Two ...
Page 12
Philips Semiconductors Light position controller handbook, full pagewidth SET SET SET 100 2 Thermal aspects The dissipation of the device is the sum of two ...
Page 13
Philips Semiconductors Light position controller 8 s handbook, halfpage 4 s active motor inactive The duration of the pause depends on the ambient temperature, see Table 1. Fig.11 Thermal transient test. Table 1 Duration of the pauses ...
Page 14
Philips Semiconductors Light position controller handbook, full pagewidth R SET = 20 k SET V SET 1996 Sep 04 PROTECTION - OVER VOLTAGE - UNDER VOLTAGE - TEMPERATURE TDA3629 SHORT-CIRCUIT I SET ...
Page 15
Philips Semiconductors Light position controller IMMUNITY TO NARROW BAND ELECTROMAGNETIC DISTURBANCES Test procedure G ENERAL INFORMATION The immunity is measured using a test procedure, which is derived from the draft international standard “ISO/DIS 11452” , parts 1 and 7, submitted ...
Page 16
Philips Semiconductors Light position controller Table 2 General test conditions for immunity measurements SYMBOL PARAMETER General T ambient temperature amb V battery voltage bat V absolute differential output voltage diff (DC value) f start frequency start f stop frequency stop ...
Page 17
Philips Semiconductors Light position controller handbook, full pagewidth CONTROL RFC 100 50 nF SET digital TEST CONTROL AND DATA AQUISITION RFC is the RF voltage injection point to control path. RFG is the RF ...
Page 18
Philips Semiconductors Light position controller V bat handbook, full pagewidth RFS R7 1.2 k CONTROL RFC R6 820 R5 820 R4 1.2 k GND RFG Feedback voltage setting J1: ...
Page 19
Philips Semiconductors Light position controller handbook, full pagewidth Fig.15 Component placement of the printed-circuit board. handbook, full pagewidth 1996 Sep IC1 Fig.16 Top view of printed-circuit ...
Page 20
Philips Semiconductors Light position controller handbook, full pagewidth Test results 30 handbook, full pagewidth V RF(rms) (V) 20 (1) (2) 10 (3) ( (1) Feedback voltage is 30%. (2) Feedback voltage is 50%. (3) Feedback voltage is ...
Page 21
Philips Semiconductors Light position controller 30 handbook, full pagewidth V RF(rms) (V) (1) 20 ( (1) RF voltage injection point to ground and to battery voltage. (2) RF voltage injection point to control path. (3) ...
Page 22
Philips Semiconductors Light position controller PACKAGE OUTLINES DIP8: plastic dual in-line package; 8 leads (300 mil pin 1 index 1 DIMENSIONS (inch dimensions are derived from the original mm dimensions UNIT ...
Page 23
Philips Semiconductors Light position controller SO16: plastic small outline package; 16 leads; body width 3 pin 1 index 1 e DIMENSIONS (inch dimensions are derived from the original mm dimensions) A UNIT ...
Page 24
Philips Semiconductors Light position controller SOLDERING Introduction There is no soldering method that is ideal for all IC packages. Wave soldering is often preferred when through-hole and surface mounted components are mixed on one printed-circuit board. However, wave soldering is ...
Page 25
Philips Semiconductors Light position controller DEFINITIONS Data sheet status Objective specification This data sheet contains target or goal specifications for product development. Preliminary specification This data sheet contains preliminary data; supplementary data may be published later. Product specification This data ...
Page 26
Philips Semiconductors Light position controller 1996 Sep 04 NOTES 26 Product specification TDA3629 ...
Page 27
Philips Semiconductors Light position controller 1996 Sep 04 NOTES 27 Product specification TDA3629 ...
Page 28
Philips Semiconductors – a worldwide company Argentina: see South America Australia: 34 Waterloo Road, NORTH RYDE, NSW 2113, Tel. +61 2 9805 4455, Fax. +61 2 9805 4466 Austria: Computerstr. 6, A-1101 WIEN, P.O. Box 213, Tel. + ...