LE24L042CS-LV-TFM-E SANYO, LE24L042CS-LV-TFM-E Datasheet - Page 10
![no-image](/images/manufacturer_photos/0/5/584/sanyo_sml.jpg)
LE24L042CS-LV-TFM-E
Manufacturer Part Number
LE24L042CS-LV-TFM-E
Description
IC EEPROM 4KBIT 400KHZ WLP4
Manufacturer
SANYO
Datasheet
1.LE24L042CS-LV-TFM-E.pdf
(10 pages)
Specifications of LE24L042CS-LV-TFM-E
Format - Memory
EEPROMs - Serial
Memory Type
EEPROM
Memory Size
4K (512 x 8)
Speed
400kHz
Interface
I²C, 2-Wire Serial
Voltage - Supply
1.7 V ~ 3.6 V
Operating Temperature
-40°C ~ 85°C
Package / Case
4-WLP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
869-1230-2
3) Noise filter for the SCL and SDA pins
4) Function to inhibit writing when supply voltage is low
5) Slave address settings
This product contains a filter circuit for eliminating noise at the SCL and SDA pins. Pulses of 100ns or less are not
recognized because of this function.
This product contains a supply voltage monitoring circuit that inhibits inadvertent writing below the guaranteed
operating supply voltage range. The data is protected by ensuring that write operations are not started at voltages
(typ.) of 1.3V and below.
This product does not come with any slave address pins, but the information of the S0, S1 and S2 slave addresses is
held internally. S1 = 0 and S2 = 0 were set for the slave addresses before shipment. During device addressing, these
slave address codes must be executed following the device code.
This catalog provides information as of June, 2009. Specifications and information herein are subject
to change without notice.
SANYO Semiconductor Co.,Ltd. assumes no responsibility for equipment failures that result from using
products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition
ranges, or other parameters) listed in products specifications of any and all SANYO Semiconductor Co.,Ltd.
products described or contained herein.
SANYO Semiconductor Co.,Ltd. strives to supply high-quality high-reliability products, however, any and all
semiconductor products fail or malfunction with some probability. It is possible that these probabilistic failures or
malfunction could give rise to accidents or events that could endanger human lives, trouble that could give rise
to smoke or fire, or accidents that could cause damage to other property. When designing equipment, adopt
safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not
limited to protective circuits and error prevention circuits for safe design, redundant design, and structural
design.
In the event that any or all SANYO Semiconductor Co.,Ltd. products described or contained herein are
controlled under any of applicable local export control laws and regulations, such products may require the
export license from the authorities concerned in accordance with the above law.
No part of this publication may be reproduced or transmitted in any form or by any means, electronic or
mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise,
without the prior written consent of SANYO Semiconductor Co.,Ltd.
Any and all information described or contained herein are subject to change without notice due to
product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the
SANYO Semiconductor Co.,Ltd. product that you intend to use.
Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed
for volume production.
Upon using the technical information or products described herein, neither warranty nor license shall be granted
with regard to intellectual property rights or any other rights of SANYO Semiconductor Co.,Ltd. or any third
party. SANYO Semiconductor Co.,Ltd. shall not be liable for any claim or suits with regard to a third party's
intellctual property rights which has resulted from the use of the technical information and products mentioned
above.
LE24L042CS
PS
No.A1440-10/10