D2-45157-QR-T Intersil, D2-45157-QR-T Datasheet - Page 10

• Manufacturer Part Number: D2-45157-QR-T
• Description: IC DGTL AMP PWM CTRLR 68QFN
• Manufacturer: Intersil
• Series: D2Audio™r
• Type: Class Dr

Specifications of D2-45157-QR-T

• Output Type: 2-Channel (Stereo)
• Max Output Power X Channels @ Load: 30W x 2 @ 8 Ohm
• Voltage - Supply: 9 V ~ 26 V
• Mounting Type: Surface Mount
• Package / Case: 68-VFQFN Exposed Pad
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Features: -

Pin Description
PIN
10
11
12
13
14
15
16
17
18
19
20
21
22
23
1
2
3
4
5
6
7
8
9
(Note 13) TYPE
TEMPCOM/
TEMPREF/
SPDIFRX
SPDIFTX
nMUTE/
nRESET
TEMP1/
NAME
VOL1/
CVDD
CGND
RGND
RVDD
RGND
RVDD
MCLK
MISO
MOSI
SCLK
SDIN
LRCK
IRQA
IRQB
TIO0
TIO1
TEST
SDA
PIN
SCK
SCL
GND
GND
GND
I/O
I/O
I/O
I/O
I/O
I/O
O
O
O
P
P
P
I
I
I
I
I
I
I
I
VOLTAGE
LEVEL
10
(V)
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
Active low reset input with hysteresis. Low level activates system level reset, initializing all
internal logic and program operations. System latches boot mode selection on the IRQ input
pins on the rising edge.
Board temperature monitor common I/O pin. When operating as output, provides 16mA
drive strength.
Two-Wire Serial data port, open drain driver with 8mA drive strength. Bidirectional signal
used by both the master and slave controllers for data transport. Pin floats on reset.
Two-Wire Serial clock port, open drain driver with 8mA drive strength. Bidirectional signal
is used by both the master and slave controllers for clock signaling. Pin floats on reset.
I
I
I
I
Output is an 8mA driver.
Core power, +1.8VDC. Used in the chip internal DSP, logic and interfaces.
Core ground.
Digital pad ring ground. Internally connected to PWMGND.
Digital pad ring power, 3.3V. This 3.3V supply is used for all the digital I/O pad drivers and
receivers, except for the analog pads. There are 2 of these pins and both are required to be
connected. Internally connected to PWMVDD.
Reference pin for temperature monitor and SPI clock. At de-assertion of device reset, pin
operates as SPI clock with 8mA drive strength. Upon internal D2-45057, D2-45157 firmware
execution, pin becomes temperature monitor reference.
Mute signal output. Low active: mute condition drives pin low. Output is a 16mA driver.
Initializes as input on reset, then becomes output upon internal firmware execution.
Volume control pulse input and SPI master- input/slave-output data signal. At de-assertion
of device reset, pin operates as SPI master input or slave output. (When operating as
output, provides 4mA drive strength.) Then upon internal D2-45057, D2-45157 firmware
execution, pin becomes input for monitoring up/down phase pulses from volume control.
(1 of 2 volume input pins.)
Board temperature monitor pin, and SPI master-output/slave-input data signal. At de-
assertion of device reset, pin operates as SPI master output or slave input. (When operating
as output, provides 4mA drive strength.) Then upon internal D2-45057, D2-45157 firmware
execution, pin becomes input for monitoring board temperature.
S/PDIF Digital audio data input
S/PDIF Digital audio data output This pin is the S/PDIF audio output and drives a 8mA, 3.3V
stereo output up to 192kHz. Pin floats on reset.
Hardware test mode control. For factory use only. Must be tied low.
Interrupt request port A. One of 2 IRQ pins, tied to logic (3.3V) high or to ground. High/low
logic status establishes boot mode selection upon de-assertion of reset (nRESET) cycle.
Interrupt request port B. One of 2 IRQ pins, tied to logic (3.3V) high or to ground. High/low
logic status establishes boot mode selection upon de-assertion of reset (nRESET) cycle.
Digital pad ring ground. Internally connected to PWMGND.
Digital pad ring power, 3.3V. This 3.3V supply is used for all the digital I/O pad drivers and
receivers, except for the analog pads. There are 2 of these pins and both are required to be
connected. Internally connected to PWMVDD.
2
2
2
2
S Serial Audio Bit Clock (SCLK) Input. Input has hysteresis.
S Serial Audio Data (SDIN) Input. Input has hysteresis.
S Serial Audio Left/Right (LRCK) Input. Input has hysteresis.
S Serial Audio Master Clock output for external ADC/DAC components, drives low on reset.
D2-45057, D2-45157
DESCRIPTION
July 29, 2010
FN6785.0