MSO3014 Tektronix, MSO3014 Datasheet - Page 12

• Manufacturer Part Number: MSO3014
• Description: Benchtop Oscilloscopes 100MHZ, 2.5GS/S 4+16 CHANNELS
• Manufacturer: Tektronix
• Type: Mixed Signalr

Specifications of MSO3014

• Equipment Type: Oscilloscope
• Sampling Rate: 2.5 GS/s
• Bandwidth: 100 MHz
• Display Type: WVGA Color 9 in
• Brand/series: MSO3000 Series
• Configuration: Bench/Portable
• Memory: 5 Mpts
• Number Of Channels: 4 Analog + 16 Digital
• Sample Rate: 2.5 GS/s analog, 500 MS/s dogtial main, 8.25 GS/s digital MagniVu
• Record Length: 5 M Points
• Input Impedence: 50Ω, 75Ω, 1MΩ
• Waveform Capture Rate: 50,000 wfm/s
• Power Analysis: Optional
• Standard I/o: (2) USB Host, USB Device, LAN, Video
• Display: 9.0 inch WVGA
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Data Sheet
Trigger System
Characteristic
Main Trigger Modes
Trigger Coupling
Trigger Holdoff
Range
Trigger Modes
Mode
Edge
Sequence
(B-trigger)
Pulse Width
Runt
Logic
Setup and Hold
Rise/Fall Time
Video
Extended Video
(optional)
I
SPI (optional)
CAN (optional)
I
(optional)
RS-232/422/485/UART
(optional)
LIN (optional)
Parallel (available
on MSO models
only)
12
2
2
C (optional)
S/LJ/RJ/TDM
www.tektronix.com
Description
Positive or negative slope on any channel or front-panel auxiliary input. Coupling includes DC, AC, HF reject, LF reject, and noise reject.
Trigger Delay by Time - 8 ns to 8 s. Or Trigger Delay by Events - 1 to 9,999,999 events.
Trigger on width of positive or negative pulses that are >, <, =, or ≠ a specified period of time.
Trigger on a pulse that crosses one threshold but fails to cross a second threshold before crossing the first again.
Trigger when any logical pattern of channels goes false or stays true for specified period of time. Any input can be used as a clock to look for the
pattern on a clock edge. Pattern (AND, OR, NAND, NOR) specified for all analog and digital input channels defined as High, Low, or Don’t Care.
Trigger on violations of both setup time and hold time between clock and data present on any of the input channels.
Trigger on pulse edge rates that are faster or slower than specified. Slope may be positive, negative, or either.
Trigger on all lines, odd, even, or all fields on NTSC, PAL, and SECAM video signals.
Trigger on 480p/60, 576p/50, 720p/30, 720p/50, 720p/60, 875i/60, 1080i/50, 1080i/60, 1080p/24, 1080p/24sF, 1080p/25, 1080p/30, 1080p/50,
1080p/60, and custom bi-level and tri-level sync video standards.
Trigger on Start, Repeated Start, Stop, Missing ACK, Address (7 or 10 bit), Data, or Address and Data on I
Trigger on SS, MOSI, MISO, or MOSI and MISO on SPI buses up to 10.0 Mb/s.
Trigger on Start of Frame, Frame Type (data, remote, error, overload), Identifier (standard or extended), Data, Identifier and Data, End of
Frame, Missing ACK, or Bit Stuffing Error on CAN signals up to 1 Mb/s. Data can be further specified to trigger on ≤, <, =, >, ≥, or ≠ a specific
data value. User-adjustable sample point is set to 50% by default.
Trigger on Word Select, Frame Sync, or Data. Data can be further specified to trigger on ≤, <, =, >, ≥, ≠ a specific data value, or inside
or outside of a range.
Maximum data rate for I2S/LJ/RJ is 12.5 Mb/s.
Maximum data rate for TDM is 25 Mb/s.
Trigger on Tx Start Bit, Rx Start Bit, Tx End of Packet, Rx End of Packet, Tx Data, Rx Data, Tx Parity Error, and Rx Parity Error up to 10 Mb/s.
Trigger on Sync, Identifier, Data, Identifier and Data, Wakeup Frame, Sleep Frame, Errors such as Sync, Parity, or Checksum Errors up to
1 Mb/s (by LIN definition, 20 kb/s).
Trigger on a parallel bus data value. Parallel bus can be from 1 to 16 bits in size. Binary and Hex radices are supported.
Description
Auto, Normal, and Single
DC, AC, HF reject (attenuates >50 kHz), LF
reject (attenuates <50 kHz), noise reject (reduces
sensitivity)
20 ns to 8 s
Trigger Sensitivity
Characteristic
Internal DC Coupled
External
(Auxiliary Input)
Trigger Level Range
Characteristic
Any Channel
External
(Auxiliary Input)
Description
0.5 div from DC to 50 MHz, increasing to 1 div at
rated bandwidth
200 mV from DC to 50 MHz increasing to 500 mV
at 250 MHz
Description
±8 divisions from center of screen
±8 V
2
C buses up to 10 Mb/s.