YB215CWCKW01/CUL-5C-CB NKK Switches, YB215CWCKW01/CUL-5C-CB Datasheet - Page 7

• Manufacturer Part Number: YB215CWCKW01/CUL-5C-CB
• Description: Pushbutton Switches SPDT, Red LED Red/White Lens
• Manufacturer: NKK Switches
• Type: Panel Seal Pushbuttonsr
• Series: YB2r

Specifications of YB215CWCKW01/CUL-5C-CB

• Contact Form: SPDT - NO / NC
• Contact Rating: 3 Amps at 125 VoltsAC
• Actuator: Plunger, with Cap
• Cap Color: Red, White
• Supply Voltage: 125 VoltsAC
• Mounting Style: Panel
• Terminal Seal: Epoxy
• Contact Plating: Silver
• Contact Material: Phosphor Bronze
• Illumination: Illuminated
• Illumination Color: Red
• Flammability Rating: UL 94 V-0
• Body Shape: Round
• Dielectric Strength: 1000 VoltsAC
• Features: Black bezel, with UL mark
• Housing Material: Polyamide, Glass Fiber Reinforced
• Insulation Resistance: 200 MOhms
• Led Size: T-1 Bi-pin
• Mounting Angle: Straight
• Operating Force: 1.5 N
• Water / Moisture Rating: IP65
• Switch Function: ON - (ON)
• Termination Style: Solder Lug
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

22mm Panel Seal Pushbuttons
1. Remove knurled
2. Remove bezel and red
3. Install LED.
4. Align tabs (B) on both
LEDs
AT634 & AT636
LED AT628
LEDs AT625G,
AT631B,
AT632F
mounting nut.
o-ring from housing.
There are two o-rings
in this assembly: one is
red, one is orange.
(+)
sides of actuator with
the projections (A) inside
of the housing and push
actuator firmly down to
snap in.
(+)
(+)
(–)
(–)
(–)
D-Flat
D-Flat
Knurled
Mounting Nut
Align D-flat on LED with Part Number
on switch for appropriate polarity and
insert LED into base.
Align D-flat on LED with Part Number
on switch for appropriate polarity and
insert LED into base.
The larger metal part within the LED
represents the cathode (–). Align LED
for appropriate polarity and insert LED
into base.
Cathode (–)
B
Part Number
This Side
Bezel
SENSITIVE DEVICES
SENSITIVE DEVICES
ELECTROSTATIC
ELECTROSTATIC
ATTENTION
ATTENTION
Housing
Actuator
Cathode
Socket (–)
Anode
Socket (+)
A
ASSEMBLY INSTRUCTIONS
Anode (+)
Red O-ring
www.nkk.com
5. Install the red o-ring which
6. Align tab inside of the bezel with keyway on housing and
7. Before installing into panel,
8. Attach mounting nut behind panel and tighten. Make
was removed in step 2 at
the inside bottom of the
bezel.
bring bezel back into its original position.
make sure that the orange
o-ring is present at the back
of the bezel. Align keyway
on bezel with tab in panel
and push switch all the way
into the panel.
sure that bezel and actuator fit properly and that there is
no space between bezel and panel. Do not overtighten.
Mounting torque: 0.785Nm (6.95 lb
Optional socket wrench AT106 available.
AT106 Socket Wrench
Housing
Red
O-ring
Bezel
Knurled
Mounting Nut
Actuator
Keyway
Orange
O-ring
Tab
Series YB2
Back of
Bezel
Panel
•
in) maximum.
Panel
Bezel
Bezel
Red O-ring
Bezel
Keyway
Tab
D121
D