YB215CWCKW01-5D-EB NKK Switches, YB215CWCKW01-5D-EB Datasheet
YB215CWCKW01-5D-EB
Specifications of YB215CWCKW01-5D-EB
YB215CWCKW01/CUL-5D-EB
YB215CWCKW01/CUL-5D-EB
Related parts for YB215CWCKW01-5D-EB
YB215CWCKW01-5D-EB Summary of contents
Page 1
... Manual Soldering: 390°C maximum for 4 seconds maximum UL94V-0 housing, base & black or metallic silver bezel File No. E44145 All solder lug models recognized 125/250V AC or 0.4VA @ 28V AC/DC maximum. Add “/CUL” to end of part number to order cULus mark on switch. www.nkk.com 22mm Panel Seal Pushbuttons ...
Page 2
... Panel Seal Pushbuttons Distinctive Characteristics 22mm pushbutton with the shortest above-panel dimension (1.8mm) in the industry for splashproof design. Meets IP65 of IEC60529 standards (similar to NEMA 4 and 13), providing dust tight and splashproof panel seal protection. Tamper resistant 19mm diameter actuator. Short body of .965” (24.5mm) conserves behind-panel space ...
Page 3
... Alternate Action with Latchdown IMPORTANT: Switches are supplied without cULus marking unless specified. Specific models & ratings noted on General Specifications page. DESCRIPTION FOR TYPICAL ORDERING EXAMPLE YB215CWCKW01-6F-JB Green, Super Bright LED Black Bezel Round Black Housing SPDT ON-(ON) Circuit D116 www.nkk.com ...
Page 4
... CONTACT MATERIALS & RATINGS G Gold Contacts Logic Level: 0.4VA max. @ 28V AC/DC max. Switch base is red TERMINALS Epoxy Seal (7.3) .288 (2.0) .079 (2.8) .110 (1.2) .047 Thk = (0.5) .020 www.nkk.com 22mm Panel Seal Pushbuttons Throw & Switch/Lamp Schematics 1 (COM) L (+) (COM (+) PANEL SEAL BEZEL (-) L ...
Page 5
... Panel Seal Pushbuttons The electrical specifications shown are determined at a basic temperature of 25°C. LED circuit is isolated and requires an external power source. If the source voltage exceeds the rated voltage, a ballast resistor is required. Base of AT634 and AT636 is Black for 5V, Light Blue for 12V and Gray for 24V. ...
Page 6
... Yellow cap (4.9) pairs with .193 amber LED to achieve amber illumination. Material for Lens & Diffuser: Polycarbonate (19.0) Dia .748 (25.0) Dia .984 YB215CWCKW01-6F-JB Panel Thickness .020” ~ .197” (0.5mm ~ 5.0mm) D120 – CAPS & CAP COLORS AT3018 Cap for ...
Page 7
... Panel Seal Pushbuttons 1. Remove knurled mounting nut. Knurled Mounting Nut 2. Remove bezel and red o-ring from housing. There are two o-rings in this assembly: one is red, one is orange. Bezel Part Number This Side 3. Install LED. LEDs AT634 & AT636 ELECTROSTATIC SENSITIVE DEVICES ...
Page 8
... Series YB2 NKK Switches can provide custom legends for caps. Contact factory for more information. Recommended Methods: Laser Etch on clear cap, Screen Print or Pad Print on cap. Shaded Area is Printable Area for Caps AT3017, AT3018 and AT3019 D (17.48) Dia .688 (19.0) Dia ...