MIL-22520/7/01 Souriau Connection Technology, MIL-22520/7/01 Datasheet - Page 25

• Manufacturer Part Number: MIL-22520/7/01
• Description: Circular MIL / Spec Connectors CRIMP TOOL FRAME
• Manufacturer: Souriau Connection Technology
• Series: JBX Seriesr
• Type: Crimping Toolr

Specifications of MIL-22520/7/01

• Product Type: Tools
• Termination Style: Crimp
• Cable Diameter: 0.7 mm to 0.9 mm, 1.3 mm
• Product: Crimping, Stripping & Cutting Tools & Drills
• Description/function: Contact Crimping
• Wire Gauge Range: 28-16
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: Contacts 0.7 mm to 9 mm, 1.3 mm

JBX Series
Push-Pull Connectors
TOOLINGS – JBX – JKX
Manual Extraction Tools
Contacts automatically extracted without pulling on the cable.
The extraction tool is the same for
both male and female contacts.
5. If inserting removable contacts:
6. Removal of contacts:
7. Take the keyed half bushing (#6) and place it over the insulator so that the window is lined up with the key on the
a. Starting with the interface end of the contact, carefully insert each contact into the backside of the insula-
a. Using the proper extraction tool insert the tool over the front of the contact and push contact out. Failure to use the
After the contact has been soldered to the wire, check each contact to insure that the contact is securely soldered
to the wire. Slide the
pre-loaded heat shrink over the solder joint and shrink into place. Do not over-heat the solder joint area as it can
cause the solder to re-flow or it could burn the wire insulation.
insulator and the key on the half bushing is pointing to the back of the insulator (position loading path indicator (worm
end)). Then take the half bushing without the window (#6) and place on the opposite side of the insulator so that both
half bushings are aligned with each other.
tor that has the position loading path indicator (worm) on it. Start with the end of the position loading path
indicator (worm) that has the half circle on it (Position #1). Then follow the position loading path indicator
(worm) around the insulator. You will go counter clockwise if using a male contact and clockwise if using
a female contact (see diagram below for the position loading path indicator (worm) layout). If the connec-
tor has center contacts, it is sometimes easier to start at the end of the position loading path indicator
(worm) (last position) and work backwards. This is up to the assembler and the process they are using to
insert the contacts. Make sure not to bend the contact when inserting it into the insulator. It is extremely
important that the contact is completely seated in to the insulator. For the connector to function properly,
the contact should click/snap into place when seated. To confirm the seating of the contact, check each
contact for proper seating.
proper extraction tool can result in damage to the contact.
Shell size
0
1
2
3
Ø Contacts
25
0.7
0.9
0.7
0.9
1.3
0.7
0.9
1.3
1.6
2.0
0.7
0.9
1.3
1.6
2.0
SOURIAU part number
JBX OUT DC07
JBX OUT DC09
JBX OUT DC07
JBX OUT DC09
JBX OUT DC07
JBX OUT DC09
JBX OUT DC16
JBX OUT DC20
JBX OUT DC07
JBX OUT DC09
JBX OUT DC16
JBX OUT DC20
JBX OUT DC1 3
JBX OUT DC1 3
JBX OUT DC1 3
ASTRO part number
ATJP 2045
ATJP 2045
ATJP 2045
ATJP 2095
ATJP 2045
ATJP 2057
ATJP 2057
ATJP 2077
ATJP 2057
ATJP 2077
ATJP 2057
ATJP 2077
ATJP 2095
ATJP 21 1 5
ATJP 21 1 5