BLM18BA750SN1D Murata, BLM18BA750SN1D Datasheet - Page 177

• Manufacturer Part Number: BLM18BA750SN1D
• Description: EMI/RFI Suppressors & Ferrites 0603 75 OHM
• Manufacturer: Murata
• Series: BLM Br

Specifications of BLM18BA750SN1D

• Shielding: Unshielded
• Test Frequency: 100 MHz
• Product: Chip Ferrite Beads
• Impedance: 75 Ohms
• Tolerance: 25 %
• Maximum Dc Current: 300 mAmps
• Maximum Dc Resistance: 0.7 Ohms
• Operating Temperature Range: - 55 C to + 125 C
• Package / Case: 0603 (1608 metric)
• Termination Style: SMD/SMT
• Dc Resistance Max: 0.7ohm
• Dc Current Rating: 300mA
• Ferrite Mounting: SMD
• Ferrite Case Style: 0603
• Inductor Case Style: 0603
• No. Of Pins: 2
• Core Material: Ferrite
• Resistance: 0.7ohm
• Rohs Compliant: Yes
• Operating Temperature Min: -55°C
• Operating Temperature Max: +125°C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

!Note
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
sales representatives or product engineers before ordering.
!Note
Do not use products beyond the rated current and rated
voltage as this may create excessive heat and
deteriorate the insulation resistance.
Mounting holes should be designed as specified in these
specifications. Other designs than shown in these
specifications may cause cracks in ceramics which may
lead to smoking or firing.
<Operating Environment>
1. Do not use products in a chemical atmosphere such
2. Do not use products near water, oil or organic
<Concerning "EMIGUARD">
VFR3V series is designed only to absorb electrostatic
surges. Do not use this product to absorb large energy
surges such as lighting or switching related surges.
<Storage and Handling Requirements>
1. Storage Period
1. Washing
2. Soldering
as chlorine gas, acid or sulfide gas.
solvents. Avoid environment where dust or dirt may
adhere to product.
Used the products within 12 months after delivery.
Solderability should be checked if this period is
exceeded.
!Caution (Rating)
!Caution (Soldering and Mounting)
Notice (Storage and Operating Conditions)
Notice (Soldering and Mounting)
Failure and degradation of a product are caused
by the washing method. When you wash in conditions
that are not in mounting information, please contact
Murata engineering.
Reliability decreases with improper soldering
methods. Please solder by the standard soldering
conditions shown in mounting information.
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
2. Storage Conditions
3. Other
(1) Storage temperature: -10 to 40 degrees C
(2) Do not store products in a chemical atmosphere
(3) When restoring taping type (BL01RN1A1F1J),
Noise suppression levels resulting from Murata's
EMI suppression filters "EMIFIL" may vary,
depending on the circuits and ICs used, type of
noise, mounting pattern, lead wire length, mounting
location, and other operating conditions. Be sure
to check and confirm in advance the noise
suppression effect of each filter, in actual
circuits, etc. before applying the filter in a
commercial-purpose equipment design.
Relative humidity: 30 to 70%
Avoid sudden changes in temperature and
humidity.
such as chlorine gas, acid or sulfide gas.
please attach the Spacer between flanges of
reel. The Spacer is corrugated paper which is
attached when shipping.
Lead Type EMIFILr !Caution/Notice
175
C31E.pdf
08.9.1
6