DE2E3KH222MA3B Murata, DE2E3KH222MA3B Datasheet - Page 16

• Manufacturer Part Number: DE2E3KH222MA3B
• Description: Ceramic Disc Capacitors Class X1 Y2 2200pF 250Vac E 20%
• Manufacturer: Murata
• Series: DE2r

Specifications of DE2E3KH222MA3B

• Voltage Rating: 250 Volts
• Operating Temperature Range: - 25 C to + 125 C
• Termination Style: Radial
• Product: Ceramic Disc Capacitors - Other Various
• Dimensions: 10 mm Dia.
• Capacitance: 2200 pF
• Tolerance: 20 %
• Temperature Coefficient: E
• Lead Spacing: 7.5 mm
• Capacitor Dielectric Type: CERAMIC DISC AND PLATE
• Tolerance,: 20%
• Tolerance, -: 20%
• Temp, Op. Max: 125(DEGREE C)
• Temp, Op. Min: -25(DEGREE C)
• Pitch,: ROHS COMPLIANT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

4
!Note
14
No.
10
11
12
13
*
*
Type KY/KH/KX Specifications and Test Methods
9
1
2
"C" expresses nominal capacitance value (pF).
"Room condition" Temperature: 15 to 35 C, Relative humidity: 45 to 75%, Atmospheric pressure: 86 to 106kPa
Continued from the preceding page.
Soldering
Effect
(Non-Preheat)
Soldering
Effect
(On-Preheat)
Vibration
Resistance
Humidity
(Under
Steady
State)
Humidity
Loading
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
Safety Standard Certified Type KY/KH/KX Specifications and Test Methods
Item
Appearance
Capacitance
Change
I.R.
Dielectric
Strength
Appearance
Capacitance
Change
I.R.
Dielectric
Strength
Appearance
Capacitance
D.F.
Q
Appearance
Capacitance
Change
D.F.
Q
I.R.
Dielectric
Strength
Appearance
Capacitance
Change
D.F.
Q
I.R.
Dielectric
Strength
No marked defect
Within 10%
1000M min.
Per Item 6
No marked defect
Within 10%
1000M min.
Per Item 6
No marked defect
Within the specified tolerance
No marked defect
3000M min.
Per Item 6
No marked defect
3000M min.
Per Item 6
Char.
Char.
Char.
Char.
Char.
B, E
E, F
B, E
E, F
B, E
SL
SL
SL
SL
SL
F
B
F
B
F
QU275+5/2C*
QU350
QU275+5/2C*
QU350
QU400+20C*
QU1000
Capacitance Change
Capacitance Change
Specifications
Specifications
Specifications
Specifications
Within 10%
Within 15%
Within
Within 10%
Within 15%
Within
D.F.V2.5%
D.F.V5.0%
D.F.V5.0%
D.F.V7.5%
D.F.V5.0%
D.F.V7.5%
1
1
1
(CF30pF)
(CU30pF)
(CU30pF)
(CU30pF)
(CF30pF)
(CF30pF)
5%
5%
As shown in the figure, the lead
wires should be immersed in
solder of 350 10 C or 260 5 C up
to 1.5 to 2.0mm from the root of
terminal for 3.5 0.5 sec. (10 1
sec. for 260 5 C).
Pre-treatment:
Post-treatment:
First the capacitor should be
stored at 120+0/-5 C for
60+0/-5 sec.
Then, as in the figure, the lead
wires should be immersed in
solder of 260+0/-5 C up to 1.5 to
2.0mm from the root of terminal
for 7.5+0/-1 sec.
Pre-treatment:
Post-treatment:
The capacitor should be firmly soldered to the supporting lead
wire and vibrated at a frequency range of 10 to 55Hz, 1.5mm in
total amplitude, with about a 1-minute rate of vibration change
from 10Hz to 55Hz and back to 10Hz.
Apply for a total of 6 hrs., 2 hrs. each in 3 mutually
perpendicular directions.
Set the capacitor for 500 12 hrs. at 40 2 C in 90 to 95%
relative humidity.
Post-treatment:
Apply the rated voltage for 500 12 hrs. at 40 2 C in 90 to 95%
relative humidity.
Post-treatment:
Capacitor should be stored at 85 2 C for 1 hr., then placed at
room condition*
Capacitor should be stored for 1 to 2 hrs. at room condition.*
Capacitor should be stored at 85 2 C for 1 hr., then placed at
room condition*
Capacitor should be stored for 1 to 2 hrs. at room condition.*
Capacitor should be stored for 1 to 2 hrs. at room condition.*
Capacitor should be stored for 1 to 2 hrs. at room condition.*
2
2
for 24 2 hrs. before initial measurements.
for 24 2 hrs. before initial measurements.
Test Method
Continued on the following page.
Thermal
Screen
Thermal
Screen
Capacitor
Capacitor
Molten
Solder
Molten
Solder
1.5
to 2.0mm
1.5
to 2.0mm
2
2
2
2
C85E.pdf
Jul.13,2011