W2SG0006-006 Wi2Wi, W2SG0006-006 Datasheet
W2SG0006-006
Specifications of W2SG0006-006
Related parts for W2SG0006-006
W2SG0006-006 Summary of contents
Page 1
... Product Datasheet A06-PDT-DOC Revision 1.64 July 10, 2009 Copyright © 2009 Wi2Wi, Inc. Wi2Wi, Inc. Doc No. A06-PDT-DOC Rev.1.64 Datasheet, GPS Module– W2SG0006 Dated: July10, 2009 ...
Page 2
... Data Sheet Status ..................................................................................................................19 9 Firmware Settings..............................................................................................................19 10 Part Numbering..................................................................................................................19 11 Certifications .....................................................................................................................20 12 References .........................................................................................................................20 12.1 Specifications .........................................................................................................................20 12.2 Trademarks, Patents and Licenses .......................................................................................20 12.3 Other ......................................................................................................................................20 Wi2Wi, Inc. Doc No. A06-PDT-DOC Rev.1.64 Copyright © 2009 Wi2Wi, Inc. Datasheet, GPS Module– W2SG0006 Dated: July 10, 2009 Page ...
Page 3
... FORMATTED DATASHEET} EK Formatted/Removed Confidential Information/Markings and added sect 7.4 information AP Update documentation to reflect change of W2SG0006 SiRF device from LP to LPx chipset. Change Current Consumption Figure for LPx Copyright © 2009 Wi2Wi, Inc. Wi2Wi, Inc. Doc No. A06-PDT-DOC Rev.1.64 Datasheet, GPS Module– W2SG0006 ...
Page 4
... Based upon the SiRFstar III™ technology, the SMD features fast acquisition times, high receiver sensitivity and low power consumption in a small, compact form factor. The W2SG0006 is a flexible design that supports a broad range of applications where GPS functionality and location based services is required. ...
Page 5
... Pin Definition The functional pin definition for the W2SG0006 is presented below in Pin Signal 1 GND 2 GND 3 GPIO9 4 VDD_3V3 5 GPS_ENABLE 6 FLASH_ENABLE 7 GND 8 GPIO4 9 GPIO13 10 GND 11 GPIO14 12 GPIO1 13 GND 14 BACKUP_CELL 15 GND 16 RXA 17 TXA 18 GND 19 VDD_3V3 20 VCC_LNA 21 VCC_ANT 22 ANT_IN 23 GND 24 RTC_OUT 25 RXB 26 TXB 27 ECLK ...
Page 6
... Pin Configuration The W2SG0006 pin SMD device. The pin definition is presented below in GND GND GND GND GPIO9 GPIO9 VDD_3V3 VDD_3V3 GPS_ENABLE GPS_ENABLE FLASH_ENABLE FLASH_ENABLE GND GND 2.3 System Block Diagram The System Block for the W2SG0006 is presented below in Figure 2. Wi2Wi, Inc. Doc No. A06-PDT-DOC Rev.1.64 ...
Page 7
... Wi2Wi can make these changes based on customer requirements. 3.3.2 GPIOs The W2SG0006 provides five GPIO pins (Pins 11, 12) for various applications. The developer may use SiRF’s GSW3 Software tools to configure these GPIO pins. Wi2Wi, Inc. Doc No. A06-PDT-DOC Rev.1.64 are those parameters beyond which permanent damage could result ...
Page 8
... GPS and Flash Enable The W2SG0006 provides Host enable input lines for GPS (Pin 5). If there is no external control of the module, then the GPS_ENABLE (Pin 5) should be tied to ground. For Programming or Firmware Upgrades the FLASH_ENABLE (Pin 6) must be set high to 3.3VDC. Note: the module will not function as a GPS receiver with the FLASH_ENABLE set high ...
Page 9
... Defined as current drawn during continuous operation at a 10Hz update rate. 3.5 Performance 3.5.1 Acquisition Time The average Time to First Fix (TTFF) for the W2SG0006 when integrated with the W2SG0006-DEV Development System is presented in 1 Parameter Hot Start – Typ. Signal @ -136 dBm Hot Start – ...
Page 10
... Antenna The W2SG0006 provides a 50 Ohm antenna launch (pin 22) for connection to either a passive or active antenna. The GPS module includes an internal LNA is designed to work with the passive antenna, but provides the bias voltage supply for an active antenna to improve the receive sensitivity. If the design is to work with an Active Antenna ...
Page 11
... BACKUP CELL 3.10 Flash Enable/Firmware Upgrade Implementation The W2SG0006 Firmware is capable of being programmed or upgraded via the UART port A (Pins 16 and 17). Please note that this cannot be accomplished from UART port B. This is accomplished using the SiRFFlash™ tool available to SiRF licensed developers. To enable the module to be programmed, 3.3VDC must be applied to the FLASH_ENABLE (Pin 6) ...
Page 12
... NMEA Input and Output Messages 5.1 NMEA Output Messages The NMEA output commands generated by the W2SG0006 are listed in Table 7. Please note that messages 152 and 154 are generated when Extended Ephemeris is enabled (in the default firmware, this feature is disabled). Message GGA Time, position and fix type data ...
Page 13
... MSK Receiver Interface 6 SiRF Binary Input and Output Messages 6.1 SiRF Binary Output Messages SiRF Binary Output Messages generated by the W2SG0006 are listed in Table 9. Please note that the support of individual commands is dependent upon the firmware loaded in the module. Table 8: NMEA Input Messages Message ID ...
Page 14
... Additional test data (Test Mode 4) SBAS operating parameters Time message for 1 PPS Track Data Extended Ephemeris Mask and Integrity Information Reserved Various status messages Copyright © 2009 Wi2Wi, Inc. Wi2Wi, Inc. Doc No. A06-PDT-DOC Rev.1.64 Datasheet, GPS Module– W2SG0006 Dated: July 10, 2009 Description Page ...
Page 15
... SiRF Binary Input Messages SiRF Binary input commands for the W2SG0006 are listed in Table 10. Please note that the support of individual commands is dependent upon the firmware loaded in the module. Hex Decimal 35 53 Advanced Power Management 80 128 Initialize Data Source 81 129 Switch to NMEA Protocol ...
Page 16
... Please refer to Section for the recommended mounting board pad layout 7.2 Outline Drawing The overall dimensions of the W2SG0006 are 15mm x 15mm x 2.5mm. The module includes a shield. 7.3 Recommended PCB Layout The recommended pad pattern for the mounting board is presented in Wi2Wi, Inc. Doc No. A06-PDT-DOC Rev.1.64 ...
Page 17
... Recommended Reflow Profile The W2SG0006 us a RoHS compliant product and requires a Lead-Free, RoHS compliant solder paste for proper manufacturing. The recommended reflow profile for the W2SG0006 is presented in 8 Figure . Assembly Guidelines: 1. Follow solder paste manufacturers recommended profile a. All RoHS solder pastes contain the same basic chemistry; however, each manufacturer may have a recommended reflow profile that performs best for their product ...
Page 18
... Equilibrium = 60 180 seconds Ramp to Maximum (Peak) temperature (245 Time above liquidus temperature (217 Wi2Wi, Inc. Doc No. A06-PDT-DOC Rev.1. +/- 25 C equilibrium C/sec max. 0 C): 45-90 seconds Copyright © 2009 Wi2Wi, Inc. Datasheet, GPS Module– W2SG0006 Dated: July 10, 2009 Page ...
Page 19
... Static navigation is enabled (suitable for navigation systems) 10 Part Numbering The following part numbering scheme is used for the W2SG0006: Part with default firmware settings as specified in Section 8 of this document: W2SG0006 Part with custom firmware settings: W2SG0006-XXX, where XXX denote the firmware version (e.g. 001, 002) Wi2Wi can create custom firmware based on the requirements of the customer ...
Page 20
... Certifications The W2SG0006 shall conform to the following standards when integrated to the W2SG0006-DEV development system. EMC/Immunity United States: FCC Part 15 Canada: ICES 033 European Union: EN 55022, IEC 1004/CISPR 22 Japan: VCCI - V series Australia New Zealand :CISPR Taiwan: CNS 13438 ...