EE-SPY301 Omron, EE-SPY301 Datasheet - Page 7

• Manufacturer Part Number: EE-SPY301
• Description: Photomicrosensors PMOD 5mmSD D-ON SS
• Manufacturer: Omron
• Series: -r

Specifications of EE-SPY301

• Output Configuration: Light-On/Dark-On
• Sensing Distance: 5 mm
• Sensing Method: Diffuse
• Termination Style: Solder Terminal
• Input Current Max: 50mA
• Optocoupler Output Type: Transistor
• Output Voltage: 1V
• Input Current: 15mA
• No. Of Pins: 3
• Opto Case Style: Module
• No. Of Channels: 1
• Operating Temperature Range: -10°C To +55°C
• Operating Voltage Max: 24VDC
• Operating Voltage Min: 5VDC
• Rohs Compliant: Yes
• Sensing Object: White Paper
• Sensing Light: Infrared
• Mounting Type: Through Hole
• Current - Supply: 15mA
• Voltage - Supply: 5 V ~ 24 V
• Package / Case: PCB Mount
• Features: Supports Connection With PLCs
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

Precautions
Refer to the Technical Information Section for general
precautions.
J WIRING
A cable with a thickness of 0.3 mm
of 2 m max. must be connected to the output terminals.
To use a cable longer than 2 m, attach a capacitor with a
capacitance of approximately 10 µF to the wires, as shown
below. The distance between the terminal and the capacitor must
be within 2 m:
Do not solder the cable to the connectors. Use the EE-1002
Connector or EE-1003 Connector (with a 1-m cable attached) to
connect the cable to the output terminals.
Use the EE1003A Connector Holder to prevent accidental
disconnection of the EE-1003 Connector from the
EE-SPY301/401/302/402 Photomicrosensor.
Do not impose excessive force on the terminals (refer to the
diagram below). Excess force will damage the terminals.
Do not disconnect the EE-1001 or EE-1006 Connector from the
photomicrosensor when power is supplied to the
photomicrosensor, or sensor damage could result.
If the metal mounting base is subjected to inductive electrical
noise, the photomicrosensor can be activated accidentally. If
noise is a problem, take the following countermeasures:
1. Connect the negative terminal to the mounting base so that
2. Connect the negative terminal to the mounting base via a
Cat. No. GC APMS-1
No
1-800-55-OMRON
OMRON ELECTRONICS LLC
One East Commerce Drive
Schaumburg, IL 60173
there will be no difference in electric potential between the
photomicrosensor and mounting base.
0.47-µF capacitor.
OUT
NOTE: DIMENSIONS SHOWN ARE IN MILLIMETERS. To convert millimeters to inches divide by 25.4.
A capacitance of
10 µF min.
5 to 24 VDC
2 m max
0 V
R
09/02
2
Terminal
or AWG22 min. and a length
Extension
cable
OMRON ON- -LINE
Global -- http://www.omron.com
USA -- http://www.omron.com/oei
Canada -- http://www.omron.com/oci
Specifications subject to change without notice.
3. Insert a plastic insulating plate with a thickness of approxi-
Wire as shown by the following illustration to connect a small
inductive load (a relay for example) to the photomicrosensor. A
diode must be connected parallel to the relay to absorb the
reverse voltage.
When using a standard switching regulator, ground the FG and G
terminal to ensure that the photomicrosensor will be in a stable
operating condition.
J POWER SUPPLY
When using a standard switching regulator, ground the FG and G
terminal to ensure that the photomicrosensor will be in a stable
operating condition.
mately 10 mm between the photomicrosensor and mounting
base.
OUT
OUT
D
Relay
OMRON CANADA, INC.
Toronto, Ontario M1B 5V8
416-286-6465
885 Milner Avenue
Switching
regulator
G
FG
0 V
5 to 24 VDC
Printed in U.S.A.