ATTINY13A-SNR Atmel, ATTINY13A-SNR Datasheet - Page 54

• Manufacturer Part Number: ATTINY13A-SNR
• Description: IC MCU AVR 1KB FLASH 20MHZ 8SOIC
• Manufacturer: Atmel
• Series: AVR® ATtinyr

Specifications of ATTINY13A-SNR

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 20MHz
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 6
• Program Memory Size: 1KB (512 x 16)
• Program Memory Type: FLASH
• Eeprom Size: 64 x 8
• Ram Size: 64 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 4x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 105°C
• Package / Case: 8-SOIC (0.200", 5.30mm Width)
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Connectivity: -

10.2.6
10.3
54
Alternate Port Functions
ATtiny13A
Unconnected Pins
If a logic high level (“one”) is present on an asynchronous external interrupt pin configured as
“Interrupt on Rising Edge, Falling Edge, or Any Logic Change on Pin” while the external interrupt
is not enabled, the corresponding External Interrupt Flag will be set when resuming from the
above mentioned Sleep mode, as the clamping in these sleep mode produces the requested
logic change.
If some pins are unused, it is recommended to ensure that these pins have a defined level. Even
though most of the digital inputs are disabled in the deep sleep modes as described above, float-
ing inputs should be avoided to reduce current consumption in all other modes where the digital
inputs are enabled (Reset, Active mode and Idle mode).
The simplest method to ensure a defined level of an unused pin, is to enable the internal pull-up.
In this case, the pull-up will be disabled during reset. If low power consumption during reset is
important, it is recommended to use an external pull-up or pull-down. Connecting unused pins
directly to V
accidentally configured as an output.
Most port pins have alternate functions in addition to being general digital I/Os.
shows how port pin control signals from the simplified
by alternate functions.
Figure 10-5. Alternate Port Functions
Note:
WRx, WPx, WDx, RRx, RPx, and RDx are common to all pins within the same port. clk
and PUD are common to all ports. All other signals are unique for each pin.
CC
or GND is not recommended, since this may cause excessive currents if the pin is
PTOExn:
PUOExn:
PUOVxn:
DDOExn:
DDOVxn:
PVOExn:
PVOVxn:
DIEOExn: Pxn DIGITAL INPUT-ENABLE OVERRIDE ENABLE
DIEOVxn: Pxn DIGITAL INPUT-ENABLE OVERRIDE VALUE
SLEEP:
Pxn
Pxn, PORT TOGGLE OVERRIDE ENABLE
Pxn PULL-UP OVERRIDE ENABLE
Pxn PULL-UP OVERRIDE VALUE
Pxn DATA DIRECTION OVERRIDE ENABLE
Pxn DATA DIRECTION OVERRIDE VALUE
Pxn PORT VALUE OVERRIDE ENABLE
Pxn PORT VALUE OVERRIDE VALUE
SLEEP CONTROL
1
0
1
0
1
0
1
0
PUOExn
PUOVxn
DDOExn
DDOVxn
PVOExn
PVOVxn
DIEOExn
DIEOVxn
SLEEP
SYNCHRONIZER
D
L
SET
CLR
Q
Q
PUD:
WDx:
RDx:
RRx:
WRx:
RPx:
WPx:
clk
DIxn:
AIOxn:
D
PINxn
CLR
I/O
Q
Q
:
PORTxn
RESET
Q
Q
CLR
D
RESET
Figure 10-2 on page 50
Q
Q
DDxn
CLR
WRITE DDRx
WRITE PORTx
D
PULLUP DISABLE
READ DDRx
READ PORTx REGISTER
READ PORTx PIN
WRITE PINx
I/O CLOCK
DIGITAL INPUT PIN n ON PORTx
ANALOG INPUT/OUTPUT PIN n ON PORTx
1
0
RRx
clk
PUD
WDx
RDx
DIxn
AIOxn
RPx
I/O
WRx
PTOExn
WPx
can be overridden
8126E–AVR–07/10
Figure 10-5
I/O
, SLEEP,