HL-5030G Omron, HL-5030G Datasheet - Page 4
![SWITCH LIMIT ADJUSTBL ROLLR LEVR](/photos/21/30/213028/4437493_sml.jpg)
HL-5030G
Manufacturer Part Number
HL-5030G
Description
SWITCH LIMIT ADJUSTBL ROLLR LEVR
Manufacturer
Omron
Series
HL-5000r
Type
Limit Switchr
Specifications of HL-5030G
Circuit
DPST (1-NO, 1-NC)
Switch Function
On-Mom, Off-Mom
Contact Rating @ Voltage
5A @ 125VAC
Actuator Type
Lever, Roller
Mounting Type
Chassis Mount
Termination Style
Screw Terminal
Operating Force
735gf
Actuator Style
Adjustable Roller Lever
Operating Force Max
7.35N
Contact Voltage Ac Max
250V
Contact Voltage Dc Max
250V
Contact Current Ac Max
5A
Contact Current Dc Max
5A
Switch Function Configuration
N.O./N.C.
Current Rating (max)
5A
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Other names
HL5030G
Safety Precautions
Refer to Safety Precautions for All Limit Switches.
Operating Environment
Wiring
Wiring Procedure
1. Loosen the cover mounting screws and remove the cover.
2. Disconnect the rubber connector from the box conduit and crimp a
3. After inserting the solderless terminal into the Switch, tighten the
4. After wiring the Limit Switch, insert the rubber connector into the
5. Tighten the three mounting screws evenly. The optimum tightening
• Seal material may deteriorate if a Switch is used outdoor or where
• Install Switches where they will not be directly subject to cutting
• Constantly subjecting a Switch to vibration or shock can result in
• The Switches have physical contacts. Using them in environments
subject to special cutting oils, solvents, or chemicals. Always
appraise performance under actual application conditions and set
suitable maintenance and replacement periods.
chips, dust, or dirt. The Actuator and Switch must also be protected
from the accumulation of cutting chips or sludge.
wear, which can lead to contact interference with contacts,
operation failure, reduced durability, and other problems.
Excessive vibration or shock can lead to false contact operation or
damage. Install Switches in locations not subject to shock and
vibration and in orientations that will not produce resonance.
containing silicon gas will result in the formation of silicon oxide
(SiO
contacts, contact interference can occur. If silicon oil, silicon filling
agents, silicon cables, or other silicon products are present near the
Switch, suppress arcing with contact protective circuits (surge
killers) or remove the source of silicon gas.
solderless terminal. The following solderless terminals are
available.
terminal screws securely.
groove of the box securely.
torque for each screw is 0.49 to 0.59 N·m.
Not Suitable
2
) due to arc energy. If silicon oxide accumulates on the
Cover
Precautions for Correct Use
Terminal
Cover mounting screw
Suitable
Rubber connector
Applicable Lead Wires
Note: Do not use wires containing silicone, otherwise a contact failure may
Applicable Solderless Terminal
The following solderless terminals are available. Do not use fork or
any other type of terminals, otherwise an accidental disconnection
resulting in a ground fault may result.
Appropriate Tightening Torque
A loose screw may result in a malfunction. Be sure to tighten each
screw to the appropriate tightening torque as shown below.
Note: If the head direction has been changed, check the torque of each screw
Vinyl cabtire cord
(VCTF)
Vinyl cabtire cable
(VCT)
600-V vinyl-insulated
sheath cable (VVF)
No.
1
2
3
4
5
result.
and make sure that the screws are free of foreign substances, and that
each screw is tightened to the proper torque.
Wire name
Head mounting screw
Cover mounting screw
Allen-head bolt
Terminal screw (M3 screw)
Switch mounting screw
(M5 Allen-head bolt)
14 max.
6.4 max.
Terminal with insulated grip
1
3.0 to
3.7 dia.
2
5
Type
conductors
Number of
2
3
4
2
2
Applicable wire
0.75 mm
0.75 mm
1 dia./1.2 dia./
1.6 dia.
Conductor
14 max.
size
4
3
tightening torque
2
2
6.4 max.
0.49 to 0.59 N·m
0.49 to 0.59 N·m
4.90 to 5.88 N·m
0.49 to 0.59 N·m
4.90 to 5.88 N·m
Appropriate
HL-5000
Round, 6 to 9
dia.
Flat, 9.4
max.
3.0 to
3.7 dia.
External
size
4