SS-10GL13T Omron, SS-10GL13T Datasheet
SS-10GL13T
Specifications of SS-10GL13T
SW247
Related parts for SS-10GL13T
SS-10GL13T Summary of contents
Page 1
... SS-01D1 0.1A @ 125VAC/0.1A plunger @ 30VDC 0.1A @ SS-01D2 125VAC/0.1A plunger @ 30VDC SS-01T 0.1A @ 125VAC/0.1A plunger @ 30VDC SS-01-E 0.1A @ 125VAC/0.1A plunger @ 30VDC 0.1A @ SS-01- ED 125VAC/0.1A plunger @ 30VDC 0.1A @ SS-01- ET 125VAC/0.1A plunger @ 30VDC SS-01-F 0.1A @ 125VAC/0.1A plunger @ 30VDC SS-01- 0.1A @ 125VAC/0.1A plunger FD @ 30VDC ...
Page 2
... SS- 10.1A @ Formed 10GL14 125/250VAC hinge lever 10.1A @ Hinge SS- 10GL2 125/250VAC roller lever 10.1A @ Hinge SS- 10GL2D 125/250VAC roller lever SS- 10.1A @ Hinge 125/250VAC roller 10GL2T lever Hole PCB - Straight SPDT 50g Unsealed 110 Quick Connect SPDT 50g Unsealed Solder SPDT 50g Unsealed Solder ...
Page 3
... Wide switching capacity range from microvoltage/current loads ( VDC to high-capacity loads 10 250 VAC) • Standard operating force, low force or super-low force models available • RoHS Compliant Ordering Information ■ Standard Type Microvoltage/microcurrent load 0.1 A max. (Bifurcated crossbar contacts) Contact Actuator OF Pin plunger 150 g ...
Page 4
... SS-5GL13T SS-5GL14-F SS-5GL14-FT SS-5GL14 SS-5GL14T SS-5GL2-F SS-5GL2-FT SS-5GL2 SS-5GL2T Soldered Tab (#110) terminal terminal SS-10 SS-10T SS-10GL SS-10GLT SS-10GL13 SS-10GL13T SS-10GL14 — SS-10GL2 SS-10GL2T min. (approx min. (approx. 100 g) 2 300 m/s min. (approx 200 m/s min. (approx Contact gap max. ...
Page 5
... OT min. 1.0 mm (0.039 in) MD max. 14.9 mm (0.587 in) OP 10.1 ± 0.8 mm (0.398 ± 0.032 in) ■ Ratings Microvoltage/microcurrent load type General purpose/resistive load Bifurcated crossbar contacts Contact form NC 125 VAC 0 VDC 0.1 A Inrush current 1 A max. SS-01-F SS-01 SS-5-F ...
Page 6
... SS-10 series must have a power factor of 0.75 min. 3. Lamp load has an inrush current of 10 times the steady-state current 4. Motor load has an inrush current of 6 times the steady-state current the switch is used circuit and is subjected to inrush current or surge, connect a surge suppressor across the switch. ■ Contact Resistance Contact rating: ...
Page 7
... Engineering Data ■ Mechanical service life Standard type (SS-5, SS-10 series) Dimensions Unit: mm (inch) ■ Pin Plunger SS-01 (-E, -F) SS-5 (-F) SS-10 ■ Hinge Lever SS-01GL (-E, -F) SS-5GL (-F) SS-10GL ■ Electrical service life Standard type (SS-5 series) Snap Action Switch SS 5 ...
Page 8
... SS-5GL14 (-F) SS-10GL14 Note: 1. Unless otherwise specified, a tolerance of ±0.4 mm applies to all dimensions. 2. Straight vertical PCB terminal models are shown above. Soldered terminal, Tab (#110) terminal, lead wire terminal, PCB terminal parallel to left and PCB terminal parallel to right are shown in the Terminals section. ...
Page 9
... Unit: mm (inch) ■ Terminals General-Purpose Type PCB terminal, straight vertical (D) PCB terminal, parallel to left (D1) Note: Thickness of all the terminals is 0.5 mm. Soldered terminal (blank) PCB terminal, parallel to right (D2) Quick-connect tab (#110) terminal (T) Snap Action Switch SS 7 ...