A22-H1 Omron, A22-H1 Datasheet - Page 199

• Manufacturer Part Number: A22-H1
• Description: LAMP A22 SER 120VAC INCANDESCENT
• Manufacturer: Omron
• Type: Incandescent Lamp, 10 mm Diameterr
• Series: A22Er

Specifications of A22-H1

• Accessory Type: Incandescent Lamp Replacement
• Illumination: Illuminated
• Height: 28 mm
• Mounting Style: Snap In
• Termination Style: Socket
• For Use With/related Products: A22 Series
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: A22E Series
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: A22H1; Z1580

Terminal Connection
Note: The above terminal connection diagrams are examples for SPST-NO + SPST-NC and DPST-NC.
A Lock Ring is provided as a standard feature.
Note: 1. When painting or coating the panel, make sure that the
Installation
Preparing the Panel
• The panel dimensions are shown below.
• The panel thickness must be 1 to 5 mm.
• Always use a 25-mm-dia. Lock Ring for a 25-mm-dia. hole.
• When painting or coating the panel, make sure that the specified
Non-lighted
Lighted without Voltage
Reduction Unit
Lighted with Voltage
Reduction Unit
IP65 degree of protection will be lost if the 25-mm-dia. Lock Ring is
not used because of the larger size of a 25-mm-dia. hole.
panel dimensions apply to the panel after painting or coating.
3.2
Panel Cutouts
Mounting to the Panel
With Lock Fitting
3.2
+0.2
2. Use an A22Z-R25 Ring when mounting to a panel with a 25-
22.3
0
+0.2
0
specified panel dimensions apply to the panel after painting
or coating.
mm diameter hole.
With Lock Ring
Type
+0.4
0
22.3
dia.
R0.8 max.
+0.4
0
24.1
R0.8 max.
dia.
+0.4
0
24.1
+0.4
0
22.3
1
2
Without Lock Fitting
1
2
+0.4
SPST-NO + SPST-NC
0
22.3
dia.
1
2
X1
X2
+0.4
Without Lock Ring
0
( )
( )
X1
X2
dia.
25
Terminal connection (BOTTOM VIEW)
X
+0.5
0
3
4
25
dia.
X
+0.5
0
3
4
dia.
3
4
Mounting the Operation Unit on the
Panel
Insert the Operation Unit (Pushbutton) from the front surface of the
panel, insert the Lock Ring and the mounting nut from the terminal
side, then tighten the nut. Before tightening, check that the rubber
washer is present between the Operation Unit and the panel.
When using a Legend Plate Frame, put one rubber washer each
between the Legend Plate Frame and the panel and between the
Operation Unit and the Legend Plate Frame. (One rubber washer will
be provided when one Legend Plate Frame is ordered.)
Align the Lock Ring with the groove in the casing, then insert the
Lock Ring so that its edge is located on the panel side.
Tighten the mounting nut at a torque of 0.98 to 1.96 N·m.
When using a Lock Ring, replace with the supplied Lock Ring, insert
the projecting part into the lock slot, and then tighten the mounting
nut.
1
2
1
2
1
2
X1
X2
DPST-NC
( )
( )
X1
X2
X
1
2
X
1
2
1
2
197