MP3V5004DP Freescale Semiconductor, MP3V5004DP Datasheet - Page 4

• Manufacturer Part Number: MP3V5004DP
• Description: IC PRESSURE SENSOR 8-SOP
• Manufacturer: Freescale Semiconductor
• Type: Differentialr

Specifications of MP3V5004DP

• Pressure Type: Differential
• Operating Pressure: 0.57 PSI, 3.92 kPa
• Port Size: Male, 0.13" (3.302mm) Tube, Dual
• Output: 0.6 ~ 3 V
• Voltage - Supply: 2.7 V ~ 3.3 V
• Termination Style: PCB
• Operating Temperature: 0°C ~ 85°C
• Package / Case: 8-SOP Dual Port
• Mounting: Surface Mount
• Pin Count: 8
• Operating Temp Range: 0C to 85C
• Operating Temperature Classification: Commercial
• Package Type: SNSR
• Operating Supply Voltage (typ): 3V
• Operating Supply Voltage (min): 2.7V
• Operating Supply Voltage (max): 3.3V
• Accuracy: 1.5 %, 2.5 %
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: 0 C
• Operating Supply Voltage: 3 V
• Supply Voltage (min): 2.7 V
• Supply Voltage (max): 3.3 V
• Supply Current: 10 mA
• Output Voltage: 0.6 V to 3 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

MP3V5004G
4
On-chip Temperature Compensation and Calibration
integrating the shear-stress strain gauge, temperature
compensation, calibration and signal conditioning circuitry
onto a single monolithic chip.
chip carrier (Case 482A). A fluorosilicone gel isolates the die
surface and wire bonds from the environment, while allowing
the pressure signal to be transmitted to the silicon diaphragm.
are based on the use of dry air as pressure media. Media,
other than dry air, may have adverse effects on sensor
performance and long-term reliability. Internal reliability and
qualification test for dry air, and other media, are available
Figure 2. Cross Sectional Diagram SSOP (not to scale)
The performance over temperature is achieved by
Figure 2
The MP3V5004G series sensor operating characteristics
Pressure
Lead
Frame
Wire
Bond
Differential Sensing
illustrates the gauge configuration in the basic
Fluorosilicone
Gel Die Coat
Element
P1
P2
Figure 4. Output vs. Pressure Differential at ±2.5% V
3.0
2.0
1.0
0.6
Die
(See Note 5 in Operating Characteristics table)
TRANSFER FUNCTION:
V
V
TEMP = 10 to 60°C
out
S
Max
= 3.0 V ± 0.30 Vdc
= V
Die Bond
S
*[(0.2*P) + 0.2] ± 2.5% V
Steel Cap
Stainless
Thermoplas-
tic
200 mm H
2 kPa
from the factory. Contact the factory for information regarding
media tolerance in your application.
interfacing the output of the MP3V5004G to the A/D input of
the microprocessor or microcontroller. Proper decoupling of
the power supply is recommended.
pressure input. Typical, minimum and maximum output
curves are shown for operation over a temperature range of
10°C to 60°C using the decoupling circuit shown in
The output will saturate outside of the specified pressure
range.
FSS
Figure 3. Recommended Power Supply Decoupling and
2
Min
O
(For additional output filtering, please refer to Application
Figure 3
Figure 4
1.0 μF
Typical
shows the recommended decoupling circuit for
shows the sensor output signal relative to
400 mm H
0.01 μF
4 kPa
Output Filtering.
Note AN1646.)
FSS
2
O
V
s
+3 V
GND
IPS
Freescale Semiconductor
V
out
470 pF
OUTPUT
Sensors
Figure 3