EM260-RTY Ember, EM260-RTY Datasheet - Page 49
![IC ZIGBEE SYSTEM-ON-CHIP 40-QFN](/photos/14/19/141902/mfg_em260-rt_series_sml.jpg)
EM260-RTY
Manufacturer Part Number
EM260-RTY
Description
IC ZIGBEE SYSTEM-ON-CHIP 40-QFN
Manufacturer
Ember
Specifications of EM260-RTY
Frequency
2.4GHz
Data Rate - Maximum
250kbps
Modulation Or Protocol
802.15.4
Applications
ZigBee™
Power - Output
-32dBm ~ 3dBm
Sensitivity
-97dBm
Voltage - Supply
2.1 V ~ 3.6 V
Current - Receiving
30mA
Current - Transmitting
34mA
Data Interface
PCB, Surface Mount
Antenna Connector
PCB, Surface Mount
Operating Temperature
-40°C ~ 85°C
Package / Case
40-QFN
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Memory Size
-
Other names
636-1003
EmberStatus
EMBER_CONNECTION_NOT_YET_OPEN
EMBER_MESSAGE_TOO_LONG
EMBER_BINDING_IS_ACTIVE
EMBER_EUI64_NOT_AVAILABLE
EMBER_INCOMING_SEQUENCED_MESSAGES_LOST
EMBER_ADC_CONVERSION_DONE
EMBER_ADC_CONVERSION_BUSY
EMBER_ADC_CONVERSION_DEFERRED
EMBER_ADC_NO_CONVERSION_PENDING
EMBER_SLEEP_INTERRUPTED
EMBER_PHY_TX_UNDERFLOW
EMBER_PHY_TX_INCOMPLETE
EMBER_PHY_INVALID_CHANNEL
EMBER_PHY_INVALID_POWER
EMBER_PHY_TX_BUSY
EMBER_PHY_UNKNOWN_RADIO_TYPE
EMBER_PHY_OSCILLATOR_CHECK_FAILED
EMBER_PHY_PARTIAL_PACKET
EMBER_NETWORK_UP
EMBER_NETWORK_DOWN
EMBER_NETWORK_PENDING_ACTIVITY
EMBER_NOT_JOINED
EMBER_JOIN_FAILED
0x73
0x74
0x75
0x76
0x77
0x80
0x81
0x82
0x84
0x85
0x88
0x89
0x8A
0x8B
0x8C
0x8D
0x8E
0x8F
0x90
0x91
0x92
0x93
0x94
A connection is not open yet.
The message to be transmitted is too big to fit
into a single over-the-air packet.
The application is trying to delete or overwrite a
binding that is in use.
The EUI64 is not available in the current packet.
One or more sequenced messages failed to be
received.
Conversion is complete.
Conversion cannot be done because a request is
being processed.
Conversion is deferred until the current request
has been processed.
No results are pending.
Sleeping (for a duration) has been abnormally
interrupted and exited prematurely.
The transmit hardware buffer underflowed.
The transmit hardware did not finish transmitting
a packet.
An unsupported channel setting was specified.
An unsupported power setting was specified.
The packet cannot be transmitted because the
physical MAC layer is currently transmitting a
packet. (This is used for the MAC backoff algo-
rithm.)
The software installed on the hardware doesn't
recognize the hardware radio type.
The software installed on the hardware doesn't
recognize the hardware radio type.
The PHY did not receive the entire packet it was
expecting from the radio.
The stack software has completed initialization
and is ready to send and receive packets over the
air.
The network is not operating.
The network has activity pending and should not
be shut down.
The node has not joined a network.
An attempt to join a network failed.
120-1003-000D
EM260
49