ATMEGA128RZAV-8MU Atmel, ATMEGA128RZAV-8MU Datasheet - Page 59

• Manufacturer Part Number: ATMEGA128RZAV-8MU
• Description: MCU ATMEGA1281/AT86RF230 64-QFN
• Manufacturer: Atmel
• Series: ATMEGAr

Specifications of ATMEGA128RZAV-8MU

• Frequency: 2.4GHz
• Data Rate - Maximum: 2Mbps
• Modulation Or Protocol: 802.15.4 Zigbee
• Applications: General Purpose
• Power - Output: 3dBm
• Sensitivity: -101dBm
• Voltage - Supply: 1.8 V ~ 3.6 V
• Data Interface: PCB, Surface Mount
• Memory Size: 128kB Flash, 4kB EEPROM, 8kB RAM
• Antenna Connector: PCB, Surface Mount
• Package / Case: 64-QFN
• For Use With: ATAVRISP2 - PROGRAMMER AVR IN SYSTEMATJTAGICE2 - AVR ON-CHIP D-BUG SYSTEMATSTK501 - ADAPTER KIT FOR 64PIN AVR MCUATSTK500 - PROGRAMMER AVR STARTER KIT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Operating Temperature: -
• Current - Transmitting: -
• Current - Receiving: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

9.2.2 Configuration
9.2.3 Register Description
5131E-MCU Wireless-02/09
Bit
0x05
Read/Write
Reset value
Bit
0x05
Read/Write
Reset value
connected to bidirectional differential antenna pins (RFP, RFN), so that no external
antenna switch is needed.
In Basic Operating Mode a transmission is started from PLL_ON state by either writing
TX_START to register bits TRX_CMD (register 0x02, TRX_STATE) or by raising edge
of SLP_TR.
In Extended Operating Modes a transmission is started automatically dependent on the
transaction phase of either RX_AACK or TX_ARET, refer to section 7.2.
The RF output power can be set via register bits TX_PWR in register 0x05
(PHY_TX_PWR). The maximum output power of the transmitter is typical +3 dBm. The
selectable output power range of the transmitter is 20 dB.
Register 0x05 (PHY_TX_PWR)
The PHY_TX_PWR register sets the transmit power and controls the FCS algorithm for
TX operation.
• Bit 7 – TX_AUTO_CRC_ON
Refer to sections 7.2.6 and 8.2.
• Bit [6:4] – Reserved
• Bit [3:0] – TX_PWR
The register bits TX_PWR sets the TX output power of the AT86RF230. The available
power settings are summarized in Table 9-1.
Table 9-1. PA Output Power Setting
Register Bits
TX_PWR
TX_AUTO_CRC_ON
R/W
R/W
3
0
7
0
Value [3:0]
0xA
0x0
0x1
0x2
0x3
0x4
0x5
0x6
0x7
0x8
0x9
R/W
2
0
R
6
0
TX_PWR
Reserved
R/W
1
0
R
5
0
Output Power [dBm]
+3.0
+2.6
+2.1
+1.6
+1.1
+0.5
-0.2
-1.2
-2.2
-3.2
-4.2
R/W
AT86RF230
0
0
R
4
0
PHY_TX_PWR
PHY_TX_PWR
59