CB-OBS411I-04-A ConnectBlue, CB-OBS411I-04-A Datasheet - Page 9
![BLUETOOTH V2.1+EDR MODULE 4DBM](/photos/14/21/142110/cb-obs411i-04-a_sml.jpg)
CB-OBS411I-04-A
Manufacturer Part Number
CB-OBS411I-04-A
Description
BLUETOOTH V2.1+EDR MODULE 4DBM
Manufacturer
ConnectBlue
Specifications of CB-OBS411I-04-A
Frequency
2.4GHz
Data Rate - Maximum
115.2kbps
Modulation Or Protocol
Bluetooth v2.1+EDR, Class 2 & 3
Applications
General Purpose
Power - Output
4dBm
Sensitivity
-84dBm
Voltage - Supply
3 V ~ 6 V
Current - Receiving
15.5mA
Current - Transmitting
25.1mA
Data Interface
Solder Pads, 2 x 20mm, 1 mm pitch
Antenna Connector
On-Board, Trace
Operating Temperature
-30°C ~ 85°C
Package / Case
Module
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Memory Size
-
Other names
809-1032
connectBlue
Copyright © 2010 connectBlue AB
* All signals are logic level UART signals (typically 0 - 2.85VDC).
** Use max 4.7kOhm as pull-down which is different to previous product generations from connectBlue.
*** Alternative signal pin recommended to use in new designs (both signal pins should be connected).
The cB-OBS411 module has linear power supplies, which means that the current is constant if the voltage supply is changed.
3.3 Characteristics
13
14
15
16
17
18
19
20
-
-
-
-
3.3.1 Power supply
-
-
-
-
-
-
-
-
19
9
10
20
NOTE
Read the
8
9
10
11
12
13
5
18,
30***
1
36
35
2
Guidelines for Efficient and Safe Use
-
-
5
3
6
4
-
-
-
-
-
-
GREEN/Switch-1 CMOS
BLUE
UART-CTS*
UART-TxD*
UART-RTS*
UART-RxD*
UART-DTR*
UART-DSR*
SerialSelect-0 /
I²C-SDA
SerialSelect-1 /
I²C-SCL
VCC_2V85
CMOS
CMOS
CMOS
CMOS
CMOS
CMOS
CMOS
CMOS
CMOS
CMOS
2.85 V
before using the modules.
In/Out
Out
In
Out
Out
In
Out
In
In
Out /
Bidirectional
Out
Out
3
4
5
6
7
8
0
9
20
19
-
This signal is multiplexed:
GREEN:Logic Green LED Signal (see the
Status
Active low.
Switch-1: If the level on this pin is pulled-down** the
unit goes back to default serial settings. The Switch-1
input is only active during the first 500ms after startup.
The module will restore all factory settings if both the
Switch-1 and Switch-0 signals are low during start up.
See the Serial Port Adapter AT command
Specification for more information on the Restoring
Default Configuration functionality.
See section
Logic Blue LED Signal (see the
section). Active low.
Note:Signal will flicker at data transmission.
See section
Clear To Send. Hardware flow control. Active low.
Transmit Data. "0" : Low, "1" : High
Request To Send. Hardware flow control. Active low.
Receive Data. "0" : Low, "1" : High
Data Terminal Ready. Active low.
Data Set Ready. Active low.
Hardware reset
SerialSelect-0: Control signal for external serial
transceivers.
See
I²C-SDA: I²C Serial data. Only used for communicating
with an external Apple® Authentication Coprocessor,
see the Bluetooth Serial Port Adapter Compatibility
iPhone and Android
SerialSelect-1: Control signal for external serial
transceivers.
See
I²C-SCL: I²C clock. Only used for communicating with
an external Apple® Authentication Coprocessor, see
the Bluetooth Serial Port Adapter Compatibility
iPhone and Android
Regulated interface voltage for voltage level shifting,
max 10mA.
Appendix Serial Interface
Appendix Serial Interface
section). Not valid until 500ms after startup.
GREEN/Switch-1
BLUE Signal
document for more info.
document for more info.
for design examples.
for design examples.
section for more info.
section for more info.
Operating Status
Page 9 of 42
Operating