ATA5429-PLQW Atmel, ATA5429-PLQW Datasheet - Page 36
![IC TXRX ASK/FSK 915MHZ 48-QFN](/photos/7/34/73471/48-vqfn-6_543-5130_01-4_sml.jpg)
ATA5429-PLQW
Manufacturer Part Number
ATA5429-PLQW
Description
IC TXRX ASK/FSK 915MHZ 48-QFN
Manufacturer
Atmel
Specifications of ATA5429-PLQW
Frequency
915MHz
Data Rate - Maximum
20kbps
Modulation Or Protocol
ASK, FSK
Applications
Alarm, ISM, Telemetry
Power - Output
5dBm
Sensitivity
-112.5dBm
Voltage - Supply
2.4 V ~ 3.6 V or 4.4 V ~ 6.6 V
Current - Receiving
10.5mA
Current - Transmitting
10mA
Data Interface
PCB, Surface Mount
Antenna Connector
PCB, Surface Mount
Operating Temperature
-40°C ~ 85°C
Package / Case
48-VQFN Exposed Pad, 48-HVQFN, 48-SQFN, 48-DHVQFN
Operating Temperature (min)
-40C
Operating Temperature (max)
85C
Operating Temperature Classification
Industrial
Product Depth (mm)
7mm
Product Height (mm)
0.9mm
Product Length (mm)
7mm
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Memory Size
-
Lead Free Status / Rohs Status
Compliant
Other names
ATA5429-PLQW
ATA5429-PLQWTR
ATA5429-PLQWTR
5.6
6. Microcontroller Interface
7. Digital Control Logic
7.1
36
2 Li Battery Application (6V)
Register Structure
ATA5423/ATA5425/ATA5428/ATA5429
The supply voltage range is 4.4V to 6.6V and VAUX is connected to an inductive supply.
Figure 5-6.
The microcontroller interface is a level converter which converts all internal digital signals that
are referred to the DVCC voltage into the voltage used by the microcontroller. Therefore, the pin
VSINT has to be connected to the supply voltage of the microcontroller.
This makes it possible to use the internal voltage regulator/switch at pin VSOUT as in
on page 7
to the supply voltage of the microcontroller as in
The configuration of the transceiver is stored in RAM cells. The RAM contains a 16
TX/RX data buffer and a 6
interface (CS, SCK, SDI_TMDI, SDO_TMDO).
The 1
The RAM and the status information are stored as long as the transceiver is in any active mode
(DVCC = VS1 or DVCC = V_REG2) and are lost when the transceiver switches to OFF mode
(DVCC =OFF).
8-bit status register is not part of the RAM and is readable via the 4-wire serial interface.
and
2 Li Battery Application (6V) with Inductive Emergency Supply
Figure 2-3 on page 9
RF Transceiver
Digital Control
ATA5423/ATA5425/
ATA5428/ATA5429
Logic
8-bit control register and is writable and readable via a 4-wire serial
SDO_TMDO
DEM_OUT
SDI_TMDI
NRESET
VSOUT
VSINT
AVCC
DVCC
VAUX
SCK
CLK
VS1
VS2
IRQ
CS
or to connect the microcontroller and the pin VSINT directly
Figure 2.2 on page
4.4V to 6.6V
VS
OUT
OUT
OUT
IN
IN
IN
IN
8.
ATmega
48/88/168
4841D–WIRE–10/07
Figure 2-1
8-bit