XBP24-AUI-001 Digi International/Maxstream, XBP24-AUI-001 Datasheet - Page 67
![no-image](/images/no-image-200.jpg)
XBP24-AUI-001
Manufacturer Part Number
XBP24-AUI-001
Description
MODULE 802.15.4 100MW U.FL CON
Manufacturer
Digi International/Maxstream
Series
XBEE-PRO™r
Specifications of XBP24-AUI-001
Frequency
2.4GHz
Data Rate - Maximum
250kbps
Modulation Or Protocol
802.15.4
Applications
Home/Building Automation, Industrial Control, ZigBee™
Power - Output
20dBm (100mW)
Sensitivity
-100dBm
Voltage - Supply
2.8 V ~ 3.4 V
Current - Receiving
55mA
Current - Transmitting
215mA @ 3.3V
Data Interface
PCB, Through Hole
Antenna Connector
U.FL
Operating Temperature
-40°C ~ 85°C
Package / Case
Module
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Memory Size
-
XBee®/XBee‐PRO® RF Modules ‐ 802.15.4 ‐ v1.xEx [2009.09.23]
Approved Antennas
OEM Labeling Requirements
Restrictions
Declarations of Conformity
XBee-PRO RF Module
Furthermore, the manufacturer must maintain a copy of the XBee user manual documentation and
ensure the final product does not exceed the specified power ratings, antenna specifications, and/
or installation requirements as specified in the user manual. If any of these specifications are
exceeded in the final product, a submission must be made to a notified body for compliance
testing to all required standards.
The 'CE' marking must be affixed to a visible location on the OEM product.
The CE mark shall consist of the initials "CE" taking the following form:
Power Output: When operating in Europe, XBee-PRO 802.15.4 modules must operate at or
below a transmit power output level of 10dBm. Customers have two choices for transmitting at or
below 10dBm:
output power of 10dBm (@ PL=4).
Additionally, European regulations stipulate an EIRP power maximum of 12.86 dBm (19 mW) for
the XBee-PRO and 12.11 dBm for the XBee when integrating antennas.
France: Outdoor use limited to 10 mW EIRP within the band 2454-2483.5 MHz.
Norway: Norway prohibits operation near Ny-Alesund in Svalbard. More information can be found
at the Norway Posts and Telecommunications site (www.npt.no).
Digi has issued Declarations of Conformity for the XBee RF Modules concerning emissions, EMC
and safety. Files can be obtained by contacting Digi Support.
Important Note:
Digi does not list the entire set of standards that must be met for each country. Digi customers
assume full responsibility for learning and meeting the required guidelines for each country in their
distribution market. For more information relating to European compliance of an OEM product
incorporating the XBee RF Module, contact Digi, or refer to the following web sites:
CEPT ERC 70-03E - Technical Requirements, European restrictions and general requirements:
Available at www.ero.dk/.
R&TTE Directive - Equipment requirements, placement on market: Available at www.ero.dk/.
When integrating high-gain antennas, European regulations stipulate EIRP power maximums. Use
the following guidelines to determine which antennas to design into an application.
The following antenna types have been tested and approved for use with the XBee Module:
Antenna Type: Yagi
RF module was tested and approved with 15 dBi antenna gain with 1 dB cable-loss (EIRP Maxi-
mum of 14 dBm). Any Yagi type antenna with 14 dBi gain or less can be used with no cable-loss.
Antenna Type: Omni-directional
RF module was tested and approved with 15 dBi antenna gain with 1 dB cable-loss (EIRP Maxi-
© 2009 Digi Internatonal, Inc.
• If the CE marking is reduced or enlarged, the proportions given in the above graduated draw-
• The CE marking must have a height of at least 5mm except where this is not possible on
• The CE marking must be affixed visibly, legibly, and indelibly.
a. Order the standard XBee-PRO module and change the PL command to 0 (10dBm)
b. Order the International variant of the XBee-PRO module, which has a maximum transmit
ing must be respected.
account of the nature of the apparatus.
CE Labeling Requirements
67