XBP24-AUI-001 Digi International/Maxstream, XBP24-AUI-001 Datasheet - Page 54
![no-image](/images/no-image-200.jpg)
XBP24-AUI-001
Manufacturer Part Number
XBP24-AUI-001
Description
MODULE 802.15.4 100MW U.FL CON
Manufacturer
Digi International/Maxstream
Series
XBEE-PRO™r
Specifications of XBP24-AUI-001
Frequency
2.4GHz
Data Rate - Maximum
250kbps
Modulation Or Protocol
802.15.4
Applications
Home/Building Automation, Industrial Control, ZigBee™
Power - Output
20dBm (100mW)
Sensitivity
-100dBm
Voltage - Supply
2.8 V ~ 3.4 V
Current - Receiving
55mA
Current - Transmitting
215mA @ 3.3V
Data Interface
PCB, Through Hole
Antenna Connector
U.FL
Operating Temperature
-40°C ~ 85°C
Package / Case
Module
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Memory Size
-
XBee®/XBee‐PRO® RF Modules ‐ 802.15.4 ‐ v1.xEx [2009.09.23]
SM (Sleep Mode) Command
SO (Sleep Mode Command)
SP (Cyclic Sleep Period) Command
<Sleep Mode (Low Power)> The SM
command is used to set and read
Sleep Mode settings. By default,
Sleep Modes are disabled (SM = 0)
and the RF module remains in Idle/
Receive Mode. When in this state, the
module is constantly ready to respond
to either serial or RF activity.
* The Sleep Coordinator option
(SM=6) only exists for backwards
compatibility with firmware version
1.x06 only. In all other cases, use the
CE command to enable a Coordinator.
Sleep (Low Power) Sleep Options Set/Read the
sleep mode options.
Bit 0 - Poll wakeup disable
Bit 1 - ADC/DIO wakeup sampling disable.
<Sleep Mode (Low Power)> The SP command is
used to set and read the duration of time in which
a remote RF module sleeps. After the cyclic sleep
period is over, the module wakes and checks for
data. If data is not present, the module goes back
to sleep. The maximum sleep period is 268 sec-
onds (SP = 0x68B0).
The SP parameter is only valid if the module is
configured to operate in Cyclic Sleep (SM = 4-6).
Coordinator and End Device SP values should
always be equal.
To send Direct Messages, set SP = 0.
NonBeacon Firmware
End Device - SP determines the sleep period for cyclic sleeping remotes. Maximum sleep period is
268 seconds (0x68B0).
Coordinator - If non-zero, SP determines the time to hold an indirect message before discarding it.
A Coordinator will discard indirect messages after a period of (2.5 * SP).
© 2009 Digi Internatonal, Inc.
• 0 - Normal operations. A module configured
• 1 - Disable wakeup poll. A module config-
• 0 - Normal operations. A module configured
• 1 - Suppress sample on wakeup. A module configured in a sleep mode with ADC/DIO sam-
for cyclic sleep will poll for data on waking.
ured for cyclic sleep will not poll for data on
waking.
in a sleep mode with ADC/DIO sampling enabled will automatically perform a sampling on
wakeup.
pling enabled will not automatically sample on wakeup.
AT Command: ATSO
Parameter
Range:
Default Parameter Value:
Related Commands: SM (Sleep Mode), ST
(Time before Sleep), DP (Disassociation Cyclic
Sleep Period, BE (Beacon Order)
AT Command: ATSP
Parameter
Range:
Default Parameter Value:
Related Commands: SM (Sleep Mode), ST
(Time before Sleep), DP (Disassociation Cyclic
Sleep Period, BE (Beacon Order)
AT Command: ATSM
Parameter Range: 0 - 6
Default Parameter Value: 0
Parameter
0-4
NonBeacon Firmware:
0-0x68B0 [x 10 milliseconds]
0
1
2
3
4
5
6
Cyclic Sleep Remote
Cyclic Sleep Remote
(with Pin Wake-up)
Sleep Coordinator*
Configuration
Pin Hibernate
(reserved)
Disabled
Pin Doze
54