AT86RF212-ZU Atmel, AT86RF212-ZU Datasheet - Page 70

• Manufacturer Part Number: AT86RF212-ZU
• Description: IC TXRX ZIGBE/802.15.4/ISM 32QFN
• Manufacturer: Atmel

Specifications of AT86RF212-ZU

• Frequency: 700MHz, 800MHz, 900MHz
• Data Rate - Maximum: 250kbps
• Modulation Or Protocol: 802.15.4 Zigbee, 6LoWPAN, ISM
• Applications: ISM, ZigBee™
• Power - Output: 10dBm
• Sensitivity: -110dBm
• Voltage - Supply: 1.8 V ~ 3.6 V
• Current - Receiving: 9.2mA
• Current - Transmitting: 25mA
• Data Interface: PCB, Surface Mount
• Antenna Connector: PCB, Surface Mount
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-VQFN Exposed Pad, 32-HVQFN, 32-SQFN, 32-DHVQFN
• Number Of Receivers: 1
• Number Of Transmitters: 1
• Wireless Frequency: 769 MHz to 935 MHz
• Interface Type: SPI
• Noise Figure: 7 dB
• Output Power: 21 dB
• Operating Supply Voltage: 1.8 V, 3 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Maximum Supply Current: 25 mA
• Minimum Operating Temperature: - 40 C
• Modulation: OQPSK
• Protocol Supported: 802.15.4
• Operating Temperature (min): -40C
• Operating Temperature (max): 85C
• Operating Temperature Classification: Industrial
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Memory Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

6.1.2.3 Frame Compatibility between IEEE 802.15.4 Rev. 2003 and 2006
6.1.2.4 Sequence Number
6.1.2.5 Addressing Fields
70
AT86RF212
Table 6-4. Frame Version Field
Bits [15:14] form the “Source Addressing Mode” subfield, with similar meaning as
“Destination Addressing Mode”.
The addressing field description bits of the FCF (Bits 0...2, 3, 6, 10…15) affect the
AT86RF212 Frame Filter, see section 6.2.
All unsecured frames according to IEEE 802.15.4-2006 are compatible with unsecured
frames compliant with IEEE 802.15.4-2003, with two exceptions: a coordinator
realignment command frame with the Channel Page field present (see [2], section
7.3.8) and any frame with a MAC Payload field larger than aMaxMACSafePayloadSize
octets.
Compatibility for secured frames is shown in Table 6-5, which identifies the security
operating modes for IEEE 802.15.4-2003 and IEEE 802.15.4-2006.
Table 6-5. Frame Compatibility
The one-octet sequence number following the FCF identifies a particular frame, so that
duplicated frame transmissions can be detected. While operating in RX_AACK states,
the received frame content of this field is copied into the acknowledgment frame.
The addressing field carries several addresses used for address matching indication.
The destination address (if present) is always first, followed by the source address (if
present). Each address field consists of the PAN ID and a device address. If both
addresses are present and the “PAN ID compression” subfield in the FCF is set to one,
the source PAN ID is omitted.
Security Enabled
Frame Control Field Bit Assignments
b
13
00
01
10
11
b
Frame Version Value
0
0
1
1
b
3
12
Frame Version
Value
b
13
0
1
2
3
00
01
00
01
b
12
Description
Frames are compatible with IEEE 802.15.4-2003
Frames are compatible with IEEE 802.15.4-2006
Reserved
Reserved
Description
No security. Frames are compatible between
IEEE 802.15.4-2003 and IEEE 802.15.4-2006.
No security. Frames are not compatible between
IEEE 802.15.4-2003 and IEEE 802.15.4-2006.
Secured frame formatted according to
IEEE 802.15.4-2003. This type of frame is not
supported in IEEE 802.15.4-2006.
Secured frame formatted according to
IEEE 802.15.4-2006
8168C-MCU Wireless-02/10