AT86RF212-ZU Atmel, AT86RF212-ZU Datasheet - Page 69

• Manufacturer Part Number: AT86RF212-ZU
• Description: IC TXRX ZIGBE/802.15.4/ISM 32QFN
• Manufacturer: Atmel

Specifications of AT86RF212-ZU

• Frequency: 700MHz, 800MHz, 900MHz
• Data Rate - Maximum: 250kbps
• Modulation Or Protocol: 802.15.4 Zigbee, 6LoWPAN, ISM
• Applications: ISM, ZigBee™
• Power - Output: 10dBm
• Sensitivity: -110dBm
• Voltage - Supply: 1.8 V ~ 3.6 V
• Current - Receiving: 9.2mA
• Current - Transmitting: 25mA
• Data Interface: PCB, Surface Mount
• Antenna Connector: PCB, Surface Mount
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-VQFN Exposed Pad, 32-HVQFN, 32-SQFN, 32-DHVQFN
• Number Of Receivers: 1
• Number Of Transmitters: 1
• Wireless Frequency: 769 MHz to 935 MHz
• Interface Type: SPI
• Noise Figure: 7 dB
• Output Power: 21 dB
• Operating Supply Voltage: 1.8 V, 3 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Maximum Supply Current: 25 mA
• Minimum Operating Temperature: - 40 C
• Modulation: OQPSK
• Protocol Supported: 802.15.4
• Operating Temperature (min): -40C
• Operating Temperature (max): 85C
• Operating Temperature Classification: Industrial
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Memory Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

8168C-MCU Wireless-02/10
Table 6-2. Frame Type Field
These bits are used for frame filtering by the third level filter rules, refer to section 6.2.
Bit 3 indicates whether security processing applies to this frame. This field is evaluated
by the Frame Filter.
Bit 4 is the “Frame Pending” subfield. This field can be set in an acknowledgment frame
to indicate to the node receiving the acknowledgment frame that the node sent the
acknowledgment frame has more data to send.
Bit 5 forms the “Acknowledgment Request” subfield. If this bit is set within a data or
MAC command frame that is not broadcast, the recipient shall acknowledge the
reception of the frame within the time specified by IEEE 802.15.4, i.e. within 12 symbols
for nonbeacon-enabled networks.
Bit 6, the “PAN ID Compression” subfield, indicates that in a frame where both the
destination and source addresses are present, the PAN ID is omitted from the source
addressing field. This bit is evaluated by the Frame Filter of the AT86RF212.
Bits [9:7] are reserved.
Bits [11:10]: The “Destination Addressing Mode” subfield describes the format of the
destination address of the frame. The values of the address modes are summarized in
Table 6-3 according to IEEE 802.15.4.
Table 6-3. Destination and Source Addressing Mode
If the destination address mode is either 2 or 3, i.e. if the destination address is present,
the addressing field consists of a 16-bit PAN ID first, followed by either the 16-bit or 64-
bit address as defined by the mode.
Bits [13:12]: The “Frame Version” subfield specifies the version number corresponding
to the frame, see Table 6-4. These bits are reserved in IEEE-802.15.4-2003.
This subfield shall be set to 0x00 to indicate a frame compatible with
IEEE 802.15.4-2003; it shall be set to 0x01 to indicate an IEEE 802.15.4-2006 frame.
All other subfield values shall be reserved for future use. See [2], section 7.2.3, for
details on frame compatibility.
100 – 111
b
b
2
Addressing Mode Value
11
000
001
010
011
b
00
01
10
11
1
b
Frame Type Value
10
b
0
Value
Value
4 – 7
0
1
2
3
0
1
2
3
Description
Beacon
Data
Acknowledge
MAC command
Reserved
Description
PAN identifier and address fields are not present
Reserved
Address field contains a 16-bit short address
Address field contains a 64-bit extended address
AT86RF212
69