RXM-900-HP-II Linx Technologies Inc, RXM-900-HP-II Datasheet - Page 20
![no-image](/images/no-image-200.jpg)
RXM-900-HP-II
Manufacturer Part Number
RXM-900-HP-II
Description
RECEIVER RF 900MHZ 8-CH PACK
Manufacturer
Linx Technologies Inc
Datasheet
1.RXM-900-HP-II.pdf
(24 pages)
Specifications of RXM-900-HP-II
Frequency
902MHz ~ 928MHz
Sensitivity
-95dBm
Data Rate - Maximum
50 kbps
Modulation Or Protocol
FM, FSK
Applications
Home / Industrial Automation, Remote Access, Security Alarms
Current - Receiving
18mA
Data Interface
PCB, Through Hole
Antenna Connector
Through Hole
Voltage - Supply
2.7 V ~ 16 V
Operating Temperature
0°C ~ 70°C
Package / Case
18-SIP
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Features
-
Memory Size
-
Other names
RXM-900-HP2
RXM-900-HP2
RXM-900-HP2
LEGAL CONSIDERATIONS
When working with RF, a clear distinction must be made between what is technically
possible and what is legally acceptable in the country where operation is intended.
Many manufacturers have avoided incorporating RF into their products as a result of
uncertainty and even fear of the approval and certification process. Here at Linx our
desire is not only to expedite the design process, but also to assist you in achieving
a clear idea of what is involved in obtaining the necessary approvals to legally market
your completed product.
In the United States the approval process is actually quite straightforward. The
regulations governing RF devices and the enforcement of them are the responsibility
of the Federal Communications Commission. The regulations are contained in the
Code of Federal Regulations (CFR), Title 47. Title 47 is made up of numerous
volumes; however, all regulations applicable to this module are contained in volume
0-19. It is strongly recommended that a copy be obtained from the Government
Printing Office in Washington, or from your local government book store. Excerpts of
applicable sections are included with Linx evaluation kits or may be obtained from the
Linx Technologies web site (www.linxtechnologies.com). In brief, these rules require
that any device which intentionally radiates RF energy be approved, that is, tested,
for compliance and issued a unique identification number. This is a relatively painless
process. Linx offers full EMC pre-compliance testing in our HP/Emco-equipped test
center. Final compliance testing is then performed by one of the many independent
testing laboratories across the country. Many labs can also provide other
certifications the product may require at the same time, such as UL, CLASS A/B, etc.
Once your completed product has passed, you will be issued an ID number which is
then clearly placed on each product manufactured.
Questions regarding interpretations of the Part 2 and Part 15 rules or measurement
procedures used to test intentional radiators, such as the HP-II modules, for
compliance with the Part 15 technical standards, should be addressed to:
International approvals are slightly more complex, although many modules are
designed to allow all international standards to be met. If you are considering the
export of your product abroad, you should contact Linx Technologies to determine
the specific suitability of the module to your application.
All Linx modules are designed with the approval process in mind and thus much of
the frustration that is typically experienced with a discrete design is eliminated.
Approval is still dependent on many factors such as the choice of antennas, correct
use of the frequency selected, and physical packaging. While some extra cost and
design effort are required to address these issues, the additional usefulness and
profitability added to a product by RF makes the effort more than worthwhile.
NOTE: HP Series-II
require external components to function. The modules are intended to allow for
full Part 15 compliance; however, they are not approved by the FCC or any other
agency worldwide. The purchaser understands that approvals may be required
prior to the sale or operation of the device, and agrees to utilize the component
in keeping with all laws governing its operation in the country of operation.
Tel: (301) 725-1585 / Fax: (301) 344-2050 E-Mail: labinfo@fcc.gov
Customer Service Branch, MS 1300F2
Federal Communications Commission
Equipment Authorization Division
Modules are designed as component devices which
7435 Oakland Mills Road
Columbia, MD 21046